The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello Bros'I have a question regarding Cisco UCS system with specs as mentioned below:UCS manager 3.1(3b)Chassis 5108Ucs FI 6248upIO module 2208xpDue to creticality I wanted to consult you regarding changing the IP addressing used in the management a...
Hello, I am very new to networking and I am currently trying to set up a lab in my computer science class. I am trying to set a forward lookup zone to our parent network's DNS server. When doing so the request says "A timeout occurred during validati...
HejI have performed a local install, but I can not login to the GUI using admin/admin.I can login to CLI with "ncs_cli -C -u admin" , but when I do "show run", all I see is snmp configuration on the device. I can not see AAA or configure it.cisco@Ubu...
Does anyone know if any cisco ASA version supports Micro-BFD (RFC 7130) ?I'm having a hard time finding it in the documentation so probably not.maybe in an upcoming release?
Cisco ACI 4.2(7s)I want to see the contract deny packet logs appear in the System>Events window for troubleshooting purposes. It currently is not being presented.I know this works because I have it working in a different ACI environment. I've looked ...
Please explain why to provide not accessible resource.According to documentation, user may access Meraki always on with following creds-DevNet Always On Read OnlyUsing the following credentials:Username: devnetmeraki@cisco.comPassword: Adm!n123!They ...
We setup an S/MIME Encryption/Decryption on a Secure Email Gateway.All works fine, accept S/MIME Decryption.We get an Error in the Logfile:Wed May 8 15:04:04 2024 Info: MID 12020615 S/MIME: Decryption failedWed May 8 15:04:04 2024 Info: MID 12020615 ...
By default ACI multipod IPN L3out OSPF external network are E2. I have requirement to change them to type E1. is it possible ? how? I tried to configure route map default export to change E2 to E1 but it did not work.
Hello,we have WLC controller in our main office and some APs in it connected to WLC.Also we have remote office with local DHCP server and some APs.Remote office is connected to main office by VPN tunnel and remote office APs are added to main office ...
Hi, we have had an issue with a rollout of new AP's on site. The AP model is 9120 and the WLC is 9800 17.9.5, Switch infrastructure is 9300L on 17.09.04aWe had rolled out 109 AP's across our site with no issues however the last 3 we have activated h...
hi , we have only one Cisco layer3 switch (C3850) in our office ,and want to enable multicast routing between two vlan 2 & 3. How should configure pim on C3850? can use spare-mode or dense-spare-mode? Can anyone pls advise? thanks in advance!
Dear all,I've set manually a specific port, in which have a non-Cisco WiFi 6 Access Point running, to provide 30W to make the PoE+ runs, but the AP itself didn't recgonize the power provided as PoE+.I've adjusted at web interface as well at CLI. Is t...
Good morning,My manager is trying to register for access to the SNTC portal but is having issues. I believe I have all relevant information - CCOID, email, contract number, serial number - but who can help us with this?Thank you,Leonard
I am having an issue with Cisco ISE and TenableSC integration. In Cisco documentation it reads that i need to upload the system and root certificates from TenableSC. By using:sudo scp /opt/sc/support/conf/TenableCA.crt [username]@[your ip address]:Te...
Good morning I am facing the following problem on a customer location with main and backup router. cisco ISR4331/K9 We see constant incoming IHQ packets on the WAN Interfaces on both routers. At the same time there is almost no traffic on the WAN Int...