The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello, Please i need someone to clarify what is the difference between the "default-originate" command and "network 0.0.0.0 - ip route 0.0.0.0 0.0.0.0 null0" commands. I see both are serving the same purpose by advertising a default route to a pee...
So if you have 2 transports from the WAN Edge, must it have ECMP to vBond in order for vBond to detect the public and private IP of both transports?Say for example you had an MPLS and Public-Internet TLOC. The Public-Internet TLOC is (unwittingly) re...
Cisco Unified CCX AdministrationSystem version: 12.5.1.11001-348 (SU1-ES03)Where does one get access to view the error repot that get generated when you click on "send error report" with the Finesse web page?
the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...
Hiiiiiiiii I have some new equipment, WS C4507R+E and i would like to have some diagnostic commands, hardware, software, CPU, even modules and supervisors, just to certify that everything is fine... Can someone helpme with some CLI comands plx?
Hello all,Long story but I had a lab upgrade from 5.2 to 6.0.5(M) fail on older APIC-M2's, and Cisco TAC suggested a fabric rebuild. Since I have newer APIC-M4's, I decided to install 5.3.2b on my APIC-M4's, and rebuild my lab fabric using those. All...
So normally a standard interface has an MTU of 1500.When creating a sub-interface on a router (or using an SVI on switch), should the MTU be manually lowered to 1496 to account for the extra 4 bytes?Everything just seems to work without this, so I am...
Hi folks,Running a Catalyst 9800-40 WLC. 1463 WAP's connected, predominantly C9136I WAP's. 8,817 active clients with 4,796 clients on our SSID using PEAP authentication via ISE on the back end. We are observing clients will frequently disconnect fro...
Hello! I am a student at college and i need some help with setup RIP.It is necessary that the network of the entire project be 197.10.19.0/24.Since I was constantly experiencing overlap when using it, I changed the subnet mask to 28.No matter how muc...
Hello. This is my first time using the Cisco community, so hopefully I don't screw it up. I'm trying to identify the specific fans used in a C9410R Cisco Catalyst Switch. The vertical fan tray on the side pulls cooling flow through the lower part ...
Dear Community,We're in the process of migrating from Cisco Prime Infrastructure Version 3.10.2 to DNAC Version 2.3.3.7. However, when running the PDART tool, it generates a report for Cisco Prime Infrastructure Version 3.10.0 and DNAC Version 2.3.5....
Hey folks,I'm looking to set up an L3out with static routes for an Active/Standby Firewalls pair, as shown in the diagram below. However, I'm feeling a bit confused, especially when it comes to configuring the L3out with SVI. Any advice on how to pro...
Where is a good source to learn what's new or differences in software revisions?For example in CUCM or UCCXWe're on 12.5, what's new in the revisions for 12.514 is our next big step, where can I learn about what's included in 14 that's not in 12.5?