Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Puzzling results when pasting in ACL config to switch
by pietro manicioto -
Catalyst 9200/9300 シリーズスイッチ show switch stack-bandwidth コマンド
by Yasuhiro Nakajima -
C8200-1N-4T における M.2 SSD ストレージ容量について
by chayu2 -
IOS-XE：FTP64 利用時の制限について
by yinanliu1 -
IOS XR: インターフェースフラップ事象の物理切り分け
by Ryota Sakaguchi -
フラグメント後に拒否されるはずの最初のパケットが拒否されない
by JapanTAC_CSC -
Upcoming Event: Capture the Flag, get the Badge!
by Tyler Langston -
HSRP Not Establishing but L2 Connectivity Verified
by 4665dridley
Community Activity
Can anyone explain “last active” and “last registered”
Cisco Unified CM AdministrationSystem version: 12.5.1.13900-152Can anyone explain “last active” and “last registered” on call manager, Find and List Phones page?It’s my understanding that “last active” displays the timestamp when a device was last ac...
Puzzling results when pasting in ACL config to switch
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
Answer phone
I have headset Bluetooth paired with cisco phones and working fine, but auto answer not work. I tried to enable Auto answer with headset on DN but still any incoming call on phone not auto answer, is there anything I miss other than configure auto an...
Set up Webex Cloud-Connected UC for on-premises devices
Is there a downtime when installing the
Enable snmp v3 command
I want to enable SNMPv3 on a Cisco router, v1/v2 is fine but v3 refuses to work. Can you help?
Multi san callmanger certificate private key distribution
Hello, Apologies for how late this question is! I have read that it is possible to generate a multi san certificate for the call manager service. Each subscriber in the cluster then uses the same certificate for call manager service. If I generate a...
CUCM upgrade from 11.5 to 15.X
Hi Team, Please advise on how to upgrade CUCM from version 11.5 (11.5.1.13900-52) to version 15.X. Is there a direct upgrade path available? If not, what are the steps for the upgrade? Thank you.
Reset mot de passe sur Cisco Nexus N3K(C-31108TC-V)
Hello, Je désire resetter le mot de passe d'un Switch Cisco Cisco N3K(C-31108TC-V). Je n'Ai pas accès au CLI via ssh ou console port. Merci pour vos retours
Como usar Port-channel nos switches Cisco Nexus
É provável que já conheças o Portchannel ou Etherchannel, comummente usado nos switches Catalyst para agregar duas ou mais portas físicas mas que logicamente pareçam uma única porta. Esta tecnologia é usada entre 2 switches para garantir maior largur...
AP-AIR2802i-B-K9 No join
l installed newest version of Wireless controller 9800-CL Cloud but wont Join DTLS Error l dont why it wont join to controller
One of the stacked switch goes to enable mode without password (9200L)
Hi,I have a problem with stacking two cisco 9200L's, after stacking, one of the pair goes straight to privileged exec mode, without enable password, while the other needs password for it. It's not the first time, this occurs, do you have any idea whe...
WLC, SSO and OEAP
Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...
Having ATA not dial 9
Newbie CUCM user -- Is it possible to set individual ATA not to dial 9 when dialing out. We do not want to globally change the dial 9 for outside call rule just certain extensions
Profiling Wired Endpoints without 802.1x or MAB using IBNS2.0
The configuration below is an IBNS2.0-based config that puts all access-mode switch interfaces into an authorized state, with no MAB or 802.1x needed, to pull device-sensor information and ship it to ISE for profiling unintrusively. It is a nice opti...
Resolved! Cisco 9300X Static routes don't work to SVI Tunnels
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
