The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Recently, my system bought around 800 of the Lenovo Gen 4 Chromebooks. We already had around 2500 Gen 3 100e's that worked perfectly fine, still do. We divided the new laptops out to the locations, and 2 of the 10 locations are having issues where th...
Hi folks,Running a Catalyst 9800-40 WLC. 1463 WAP's connected, predominantly C9136I WAP's. 8,817 active clients with 4,796 clients on our SSID using PEAP authentication via ISE on the back end. We are observing clients will frequently disconnect fro...
CUCM 14SU3, SBC 8300 v17.09.04a We moved off TDM PRIs over to new SBCs for all calling. Testing since November with no issues. We ported our DNs to the carrier on 17 April from our old carrier and I set up inbound calling to come in across the SIP ...
Hi community, I'm trying to collect DHCP packets from a Nexus 5500 and the problem I have is that the capture is interrupted randomly, so I nbeed to keep looking at the console to re-run it again, and some times it takes me some tries to get it worki...
I have a AP2802e and was wondering if i could connect 2 antennas (ANT2566P4W-R)on it , one using the normal connectors and the other would be connected using a DART connector(AIR-CAB002-DART-R). . Dart connectorAntenna ANT2566P4W-R
I have a couple of switches that are trunked via a LAN cable from another switch. I noticed that these switches sometimes have a hard time to SSH into. I get the error: "Connection timed out". After a while and a few tries I can connect just fine. I ...
Hello!We are currently using a voice translation rule to reject calls from specific numbers at the CUBE level (see attached screenshot), but we have reached the maximum (100) and I haven't been able to stack multiple voice translation rules on the in...
Hi to all.i have enabled in the second 40G slot of a 9407 with SUP1 a huawei 40G interface as in the png attached.The switch does not seem to have understood that. It rus 17.06.04.Chassis Type: C9407RMod Ports Card Type Model Serial No.---+-----+----...
HI, we have project requirement to integrate the Iridium Satellite phone integration with Cisco PABX to make a calls in case of emergency. Can you please suggest, what can we achieved with this interface.1) can we make calls on any number at cisco PA...
Hello Team, I have a customer that wants to push out a macro (already confirmed working on single unit) to remaining deployment. They also want to mass update the UI on the touch to support the new macro functionality. I'm able to export both the U...
Hello,we have WLC controller in our main office and some APs in it connected to WLC.Also we have remote office with local DHCP server and some APs.Remote office is connected to main office by VPN tunnel and remote office APs are added to main office ...
the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...
Hi, One of the our client want to use Different make WAN router (not cisco) for WAN connectivity. At the same time, they wanted the backup call manager option for their cisco phones. Can we use SRST router somewhere middle of the network without any ...
Hello, I have deployed EWC and around 20 AP are joined to the EWC. There was a scenario where there was a power outage. Post the power issue was resolved, All the Aps but three have re-joined the EWC. Those three Aps were showing on the switch , but ...
Using ISE as Radius for device login. Have a primary/secondary server, both synced and apparently no issues. However, Radius authentication only works for a short time and only after we make a change and save it. We are using DUO MFA, and we get the ...