Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1927251members
1239884discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

MTU for SVL

Is it necessary to change the MTU for SVL links in a scenario in which interfaces are configured with MTU larger than default 1500 bytes?Traffic could flow between chassis through SVL links in a Stackwise Virtual cluster. Could not find any reference...

ckuwajima by • Level 1
  • 0 Views
  • 0 replies
  • 0 Helpful votes

FTD: Again - Unable to reach Cisco Cloud from the device

Hello everybody, our customer is using the FMCv rel. 7.2.5.1 and many FTDs.After de-register/re-register the FMC in the Smart Software Manger because another error message four devices (7.0.1 & 7.0.5) fourdevices show the error: Threat Data Updates o...

swscco001 by • Level 1
  • 144 Views
  • 4 replies
  • 0 Helpful votes

Created a Route Based IPSEC Tunnel on Cisco FTD 2140

I have a Cisco FTD 2140 Secure Firewall that I am trying to build a route based IPSEC tunnel using VTI's. The vendor needs my proxy ID or encryption domain to be presented as a public IP address. So my WAN IP is obviously public but my internal netwo...

ccna_don by • Level 1
  • 114 Views
  • 4 replies
  • 0 Helpful votes

Answer phone

I have headset Bluetooth paired with cisco phones and working fine, but auto answer not work. I tried to enable Auto answer with headset on DN but still any incoming call on phone not auto answer, is there anything I miss other than configure auto an...

matee by • Level 1
  • 47 Views
  • 1 replies
  • 0 Helpful votes

Cisco 561 USB Y cable RJ9/RJ11 replacement

Hello,  We have a user that has misplaced the USB Y cable RJ9/RJ11 that came with the 561 multibase.  They use that cable to connect to a 7841 phone.  I do not see that cable listed a spare to purchase in the data sheet or in CCW.  Any advice on what...

AP-AIR2802i-B-K9 No join

l installed newest version of Wireless controller 9800-CL Cloud but wont Join DTLS Error l dont why it wont join to controller 

lisavbedt by • Level 1
  • 7 Views
  • 0 replies
  • 0 Helpful votes

Allow ISE captive portal DNS entry on outside DNS.

Hello,We are having ISE for EAP/TACACS authentication and, hosted internally in our datacenter.Now we have configured BYOD captive portal that tied to AZURE SAML authentication, the current captive portal redirect URL from ISE has prepended the node ...

kshah2589 by • Level 1
  • 1386 Views
  • 21 replies
  • 0 Helpful votes

Resolved! PBR VS CONNECTED

hello. I understand that Connected routing has an AD value of 0. The IP bands on the 1st and 2nd floors are different. 1st floor: 1.1.1.0/242nd floor: 2.2.2.0/24 There are two firewalls on top of the backbone. The band will be 3.3.3.0/24. If you conf...

김선명 by • Level 1
  • 207 Views
  • 8 replies
  • 0 Helpful votes

SRTP config

Hi All, I'm trying to establish a SIP trunk to an ITSP using TLS and SRTP. We think we have done all the trust point stuff and TLS seems to be OK. However, I'll a little lost on the SRTP. Looking at several guides looks like a few different methods. ...

vManage SDWAN PCAP scripting help.

Good morning all!I am working on a project on our SD-WAN. I am new to SDWAN and vManage and was asked to look into possibly scripting some packet captures over a period of time. Our SDWAN consists of several IR1101's and they can only be managed via ...

Having ATA not dial 9

Newbie CUCM user -- Is it possible to set individual ATA not to dial 9 when dialing out.  We do not want to globally change the dial 9 for outside call rule just certain extensions 

Unable to ping between two tunnel points

Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...

Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: