The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Good day to everyone.I have two Cisco ASA running on FPR2130 assembled into a balancing group, for example:vpn-gw1.example.comvpn-gw2.example.comgeneral address vpn.example.com.Firmware version 9.18.3.56Anyconnect 4.10.07062At the moment, all our emp...
I have an ATA192-3PW-K9 V04 and cannot get it to register. I have it flashed to the latest firmware. I created the device as a workspace with it's mac address and DID/extension in Webex. When I factory reset the device, all I'm doing is going to voic...
OK, so I've got a set of ASA's and we are migrating them to Firepowers, and all seems ok. In the past we have noticed that for some reason on the ASA's, no matter what you specify as the parameters for phase 1, the rekey timer always connects at 3600...
We are a healthcare facility. For past several months we have had several complaints from users that calls are often full of static. We are running CUCM 12.5(1)SU8 and the phones are primarily 8811 running current firmware. We have replaced phon...
Hello Everyone, I am contacting you all because i don't seem to find the needed information to resolve my issues, even though there are many similar topic as mine with the same error.We have an infrastructure using FTD ASA5506 with switch CISCO WS-C2...
Presentación del webinar Community Live Con la colaboración de Edgar Arenas y Martín Arias. En las redes de hoy en día, diferentes tipos de tráfico recorren por los nodos del proveedor de servicio. Cada tipo necesita un tratamiento diferente según la...
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Fixing cast iron without welding can be effectively accomplished through the use of a metal epoxy. This method involves cleaning the broken pieces thoroughly to remove any dirt, grease or rust. Once clean, apply a high-quality metal epoxy over the br...
After searching through other posts, my config seems OK but still strange behaviourasa 9.20 running on FPWR chasisI cannot get in enabled mode when connecting to ASA via console.It used to work but stopped after I played (disable and restore) with aa...
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
hi i am trying to cable up trhe ucs 6454. I got 2 40G mopdules on port 53 and 54 on each fabric. I got 2 core switches to connect therm to FABRIC 1port 53 ----> port 1 on Core switch APort 54 -----> port 1 on Core Switch BFABRIC 2port 53 ------> port...
I am user with customer administrator role but still unable to get access to EOX API . When in try API request I get eh below 403 Forbidden error. Do let me know if any other details is needed.
Hello,I have a C1300, I use it as my IPv4 and IPv6 gateway for internal routing. It has a default gateway to another router for internet access. If I perform an IPv6 speedtest with the c1300 as my gateway for IPv6 then I get around 1Mb, this is stran...
Deployed a 3100 in chassis mode to the FMC a few days ago. All went to plan.Determined we needed to change the IP so decided just to delete the device from FMC and re-provision it.On the FTD via local-mgmt did a erase configuration. The device wiped ...