The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Dear Community,I'm asking for you guidance. I have come across a challenge on Cisco ASA version 9.8. Need to allow a web server to be access outside(Public) from DMZ Zone to Ouside Zone. Per below configuration template. Nat is transilating but acce...
I'm struggling to understand connectivity problem between a switch and firewall. The Nexus is located between the Core switch and the edge firewall. It's purpose is to divert traffic via ITD for content filtering. My problem right now is that I'm n...
Hi,We have mGRE DMVPN tunnle between one Hub and 7 Spokes. Other 6 Spokes are working fine but one Spoke is not connecting to Hub.Spoke shows DMVPN on IKE state (tunnle is not working) and Hub is not adding nhrp entry in table.Spoke DMVPN TunnelPleas...
Hi AllI have a S2S VPN connected at phase 1, however doesn't successfully negotiate Phase 2. The issue I have is that my Cisco FTD sits behind a NAT device. I have configured NAT-T.My configuration on my FTD has the local peer configured with the pri...
I have an intermittent internet cut off after around some days of working (5 to 10 days). The router becomes inaccessible by ssh. No ping also from internet and from inside. The architecture includes two switches (CBS350-48FP-4X) with Vlan1.We did no...
Hi, as the title says, I am unable to connect to my Cisco Secure VPN after updating my OS from Ubuntu 22.02 to 24.04. The error I receive is"You are missing the required libraries for the authentication method you requested."Upon closer inspection, t...
Recently I've seen some switches show ports with a status of "notconnect:" What does the colon at the end signify?I don't have it documented where all I've seen it but I just now saw it on a 6 stack of WS-C3650-48PD running 16.12.06. About 85% of ou...
Hello Professionals,I setup the NTP server in one of branch site and would like to make all network switches to see this server including other branches. - NTP server: 10.10.10.158 (placed in CST timezone, it refers pool.ntp.org) - NTP Client: Switch...
Hi guys we had an issue routing to webex calling to our on prem cucm via the trunk.we could not dial webex users from our cucm via the trunk, but we could dial the same numbers from webex to cucm.i added a route to the source number from webex to poi...
I'm speaking of Essentials/Advantage/Premier. We use on-prem SSM.is there way to know how many licenses Cisco ISE gets from the binding to a virtual account on Cisco SSM?The only piece of information is the consumed ones, like knowing how many you ar...
Howdy Cisco Community!Need your help as fairly new trouble shooting site to site VPN connectivity.I am unable to establish VPN connectivity per information below.Site:1crypto ipsec ikev2 ipsec-proposal CSM_IP_1protocol esp encryption aes-256protocol ...
Gentlemen, Good morning. Need help.I shared some information in the case https://community.cisco.com/t5/smart-net-total-care-portal-and-collector-discussions/is-it-possible-to-have-two-profiles-on-the-sntc-portal/td-p/5022088 And I got support to cre...
Gents, Which table does the dialed number gets stored in. I need to know how to find the dialled number rather than manually going through each dialed number list as this can be very time consuming as you can imagine. Thanks
Hello together, I want to upgrade to a Cisco Catalyst 9500. I enter the following command:install add file bootflash:cat9k_iosxe.16.09.04.SPA.bin activate commit The following line I confirm with Yes:Please confirm you have changed boot config to boo...
Hello,I need guidance with SPA3102.Line 1 is connected to a SIP trunk and I can make calls (outbound) from the analog telephone (ATA)PSTN Line is also connected to the same SIP trunk, and I need to receive calls (incoming) from the trunk number to th...