Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1937890members
1264834discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

ESA Cluster query

Hi All, Need to configure an Cluster between Hardware device and Virtual appliance and later will remove the Hardware appliance. Before jumping into configuration i have a some query. 1. Is it sma required after forming an cluster to manage the devic...

Vishal6 by • Level 1
  • 239 Views
  • 12 replies
  • 0 Helpful votes

nexus 7000 eem not runnig cli commands

Hi, I am tryning to run a python script from a eem to send an email and I notice that I am no capable of running any cli command from the eem.  eem example: event manager applet sendemail event cli match "conf t" action 0.5 cli command "enable" actio...

igmp in ISE DACL syntax check fail

I get a syntax check error when the ISE DACL has permit igmp any 224.0.0.0 15.255.255.255.  The ACL is accepted and works on a switch if statically configured.  However, ISE syntax check gives the below error.  Any suggestions?"permit igmp any 224.0....

tachyon05 by • Level 1
  • 13 Views
  • 2 replies
  • 0 Helpful votes

Microsoft RDP application and Yubikey 5

Hi All,I'm attempting to setup a Yubikey 5 as the authentication method for logging into an RDP session on an AWS site that is protected by the Microsoft RDP application.I have users setup using Duo Mobile and it works fine, but one user doesn't have...

Dan110_0-1715705000066.png
Dan110 by • Level 1
  • 1 Views
  • 0 replies
  • 0 Helpful votes

ASR BGP problem

the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...

SD-WAN Validator 20.14 Template issue

Hi, I'm configuring the SD-WAN Control Components 20.14 for a lab. I successfully created and attached a device templates with feature templates for the manager and the controller. I created a vEdge Cloud template for the Validator (vBond). But when ...

dbillon by • Level 1
  • 1 Views
  • 0 replies
  • 0 Helpful votes

C8300 IOS missing whilst password recovery disabled

So this is a tricky one.   One of my engineers has managed to remove the IOS files from a C8300 while configuring, they made the classic mistake of walking away and then coming back to the work half way through a step. They copied across the new IOS ...

Resolved! Routes behind a tunnel-te unlabelled

I have created a tunnel-te from xrv16 to csr3, the tunnel is up and getting Pop label to csr3 that's ok.From xrv16 I have learned the route to xrv17 over the tunnel, but checking the Label it's unlabbled as well.I believe the route from xrv16 to xrv1...

ise stuck in configuration memory testing memory

we have a cisco ISE 3595 and I rebooted it by typing reload in the cli. I finally hooked up a vga connection to a monitor and its just stuck on "configuration memory testing memory", keyboard seems unresponsive. I tried connecting from the I/O in the...

Emergency Responder - Multiple Emergency Numbers

At one of my customers, I am implementing CER for emergency dialing (obviously). I have configured and tested 911 call routing. All call routing for emergency services stays on sight (calls go to the on site security desk) and right now 911 is the ...

Load more