Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1929170members
1243287discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

WLC9800 map two vlans on the same ssid

Hello, I have a WLC9800 with 9115 APs.For clients, I have a Vlan (100) mapped to an ssid. I want to add another vlan (102) mapped to the same ssid.I have added the vlan 102 (configuration, layer2, add vlan), i have created a vlan group and added both...

NTP and Syslog packets with specific IP Address

Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...

Ranjita by • Level 1
  • 6 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Restarting DRF Services

I just wanted to verify before I did it, that I can restart the DRF services on my CUCM 7.0 without disrupting anything but backups right? A job seems to be hanging and I can't configure anything because it says that a backup is in progress, even tho...

アクセスポイントWAP150 シングルポイント

お世話になります。 クラスター設定で質問です ①シングルポイント設定あたりのWAPデバイス数 WAP150：4とありますクラスターを作成する場合 ４台までの接続に限るということですか？？ ②作成したクラスターにAPを登録する場合新しいクラスターを作成で 既存クラスター名で登録するのか？ 既存クラスターに追加で登録するのか？ 既存クラスターで登録した場合SSID等が CISCOSB-setupになってしまう なぜか？？ 

HiroHiro0000_0-1711073144590.png

Resolved! Trunk commands for ISR ESM?

Hello,At my home, I had an 8 port 2960G switch die after a power outage today.  I replaced it with a ISR 1921 that has an 8 port ESM.  It's been a very long time since I messed with configuring ESMs...  My plan was to just copy over all of the switch...

WSA

hello all, is it possible to access physical cisco WSA GUI without  license ???  

yoseph by • Level 1
  • 1 Views
  • 0 replies
  • 0 Helpful votes

9800 WLC-Same Vlans on multiple sites in SD-WAN setup

I have a 9800-CL in an SD-WAN setup. I have multiple sites that have the same Vlans at each site to make it easier to manage and remember.Ex:NorthSite: data-4, voice-5, wifi-6SouthSite: data-4, voice-5, wifi-6etc...My current WLC configuration has on...

GeorgeC71 by • Level 1
  • 133 Views
  • 6 replies
  • 0 Helpful votes

Cisco 9200 Mgmt VRF

Hi All,  am using Cisco 9200 switches and assigned management IP as under mentioned. I have some other servers which are using the same IP network and with VLAN 10 , but am not able to ping switch from my laptop configured with VLAN 10 . Can you plea...

uni1389 by • Level 1
  • 73 Views
  • 3 replies
  • 0 Helpful votes

Problems with SNMP on the ASA 5555-X

Hello everyone,I have a CISCO ASA 5555-X configured in multi-context mode and I want to monitor it via SNMP.However, I can't find the MIB files for this device.How can I get them?I don't have access to ftp://ftp.cisco.com/pub/mibs/supportlists/asa/as...

vsmjoao14 by • Level 1
  • 148 Views
  • 5 replies
  • 0 Helpful votes

AIR-AP2802I-E-K9 fail to join

Hello ,We are having problem with one AP to join the WLC , all others successfully the controlle. the console output is :[*03/19/2024 09:08:50.0003] CAPWAP State: DTLS Setup[*03/19/2024 09:08:50.0035] dtls_process_packet: DTLS Error: 1040[*03/19/2024...

zillams by • Level 1
  • 303 Views
  • 7 replies
  • 0 Helpful votes

Access Point WAP150 Single Point

I have questions in cluster settings.   (1) Number of WAP devices per single point setting WAP150:4 Does the setting 'WAP150:4' indicate that a maximum of 4 WAP devices can be connected in a single cluster?   (2) Registering an AP in a Created Clu...

HiroHiro0000_0-1711073144590.png
Translator by • Community Manager
  • 58 Views
  • 1 replies
  • 0 Helpful votes
Load more