The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello Folks, I have a pair of ASA5516 with HA mode, ISP provides a high-speed WAN 500Mbps up/download, while doing some speed tests recently we noticed that all our tests from the inside network are not bypassing 100mbps, I checked all inside/outside...
Where I work we are having some problems with sending bulk email from a single public IP address, as several emails are being blocked or delayed.Currently the server has a 1-to-1 NAT with a specific .73 IP address.The request I got is to distribute e...
Does anyone know if any cisco ASA version supports Micro-BFD (RFC 7130) ?I'm having a hard time finding it in the documentation so probably not.maybe in an upcoming release?
Attempting to login on CSPC for a long time and my password got expired. The prompts says that I haven't specified the password reset questions and answers which is not true as this used to work before. My question is: can I reset my CSPC account fro...
Good morning I am facing the following problem on a customer location with main and backup router. cisco ISR4331/K9 We see constant incoming IHQ packets on the WAN Interfaces on both routers. At the same time there is almost no traffic on the WAN Int...
I am experiencing high cpu usage on one of my 4500x switches. Below is the output switch#show processes cpu sortedCore 0: CPU utilization for five seconds: 37%; one minute: 32%; five minutes: 29%Core 1: CPU utilization for five seconds: 19%; one min...
Hello Cisco community, i've got a weird problem. I have a server "A" connected to Gig2/0/16 as an access port (VLAN28) to my Catalyst C9300 switch (Two stacked switches). I can ping the device from within the switch. The switch has an SVI configured ...
Hello everyoneI have a cisco Catalyst C2960X and configured radius.I have configured it, but when I try to test group aaa, there is the following information:User authentication request was rejected by server.Then I checked the radius server clearpas...
Ask Me Anything Forum - Drive to 15X Welcome to the Cisco Support Community Ask Me Anything discussion! Are you considering upgrading or migrating your UC applications to version 15.x, such as CUCM, CUC, IM&P? If you're looking to learn more about...
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)Router uptime is 1 minuteSystem returned to ROM by error - a Software forced crash, PC 0x30EEBBE8 at 06:3 9:57 UTC Wed May 8 2024System image file is "flash0:c2900-universalk9-mz.SPA.1...
Hi all,I work for a mid sized financial firm with a total network device count of less than 100, mostly consisting of catalyst 9k (core and access switches), with handful of nexus 9k, MDS 9k, ISR4k, a pair of WLC5520s in SSO (AP3802s), and a dozen F...
1. We are interested in gathering information about LAN based devices used in Cisco. 2. We are keen to learn about any ongoing or potential improvements being considered for LAN-based solutions within Cisco based on the devices stated in Q1.
Hi ,I have configured the packetfence according to guide , but when i go to connect the SSID. its directly connect and reach the internet and not redirected toward web auth page.i cant find any logs and anything else to troubleshoot. pls check my con...
So I have a network setup and everything seems to work fine. I have 3 OSPF areas and running MPLS VPN (MP - BGP all configured) Area 65 ---- Area 0 ----- Area 78 I am trying to create a tunnel from one router in Area 65 to another router in router...