Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
ssh into a switch - no matching key exchange method found
by fabioairoldi -
Is there a CLI to monitor traffic stats on a l2transport interface?
by ThomasD86 -
Two Mac addresses from the FTD 2110 MGMT interface
by willpkk01 -
L3 Switches connecting to Firewalls
by Ranjita -
Setting UP a SECOND ASA5506-x firewall
by Myleslandish -
Site-to-Site IPSec with VTI - Initial delay up to 60 seconds
by Plamen Mladenov -
Empowering Sustainability with Cisco and adidas
by Sabah Kadir -
Static Routes on FTD 2130 using CLI
by Knassi
Community Activity
Static Routes on FTD 2130 using CLI
Has anyone Created statoc route on the FTD sensor via the CLI?Mine looks like it goes throught bu when i FDM into it, i do not see them. Any Advice will be appreciated.Thanks.
Resolved! Switch not reliably forwarding DHCP requests
Hi, hopefully this is the right place for this question. We have a switch stack of three 9300 switches running IOS XE that handle networking for the office area. The office machines sit on a single vlan. DHCP is provided by a Linux DHCP server sitt...
A guide to SIP Normalization on CUCM and Lua Scripting
I have recorded this guide for SIP Normalization on call manager and also have elaborated a little bit on how we use the Lua scripting. A SIP Normalization script could really help the customer as a workaround or a permanent solution for issues rel...
Need a complete guide for WS-C2960X & how do i configure policing/qos
Where do i find the complete guide on my switch?This is the model number WS-C2960X-48FPS-L.The software version is c2960x-universalk9-mz.152-2.E3What I'm looking to do is limit how much bandwidth is allowed on an interface. The network at that site o...
Resolved! Mobility Express Upgrade Failure
Hello, I am in the process of updating a Mobility Express WLC from Cisco. I have deployed the TFTP server and the correct images and the pre-download worked on all access points except one. In the following picture you can see what output I get. I l...
Lost ARP Announcement Packet for Meraki MR30H Access Point
Hi,I have a setup with following components.* Cisco - Meraki MSS120-8FP Gigabit Ethernet Switch* Cisco - Meraki MR30H Access Point (POE)* GRMS Device with LwIp Stack* 2 PC with Windows 10.* My PC (Windows) to pingWhen I try to ping the GRMS device t...
Web Gui issues with C1121-4P router
I set up a C1121-4P router for a friend with int gig0/0/0 facing the ISP with ip address dhcp. int gig0/0/1 192.168.1.1/24. See attached sh run. Vanilla Configuration not much security or complexity. After a power reload the GUI "https://192.168.1.1/...
ASR1001-X Thruput only 750 meg Interfaces10G both sides -Circuit 10G
We have a Cisco ASR1001-X and it can only pass 750 megs of traffic thru it on a 10 Gig circuit. I looked at licensing levels and they seem correct. Anyone have any ideas of what I can look at? Both Lan and Wan interfaces are 10 gig and Wan is using S...
WebUi access for catalyst 3650
I am trying to access the WEB UI but it is giving me error:ERR_SSL_VERSION_OR_CIPHER_MISMATCHThe client and server don't support a common SSL protocol version or cipher suite.I am using client with Windows 2019 server OS.. Chrome Version 123.0.6312....
using bypass codes for a VA
I am trying to figure out the best way to give a VA access to certain accounts without giving her the login info. My thought is to share passwords via LastPass (or other password manager), but not not so the password shows. For 2FA, use a bypass code...
Sfr module upgrade aborted
Hi Guys, Tried to perform the reimage of the Cisco 5525-x firepower module to 6.0.0 but failed. I've setup the ftp server(filezilla) and uploaded the boot image to disk0 parttion without any issue, however, perform system image ftp://username:passwo...
Nesux-FAN-Speed-100%
Facing FAN speed 100% issue in nexus Nexus 93180YC-EX switch.
Allow ISE captive portal DNS entry on outside DNS.
Hello,We are having ISE for EAP/TACACS authentication and, hosted internally in our datacenter.Now we have configured BYOD captive portal that tied to AZURE SAML authentication, the current captive portal redirect URL from ISE has prepended the node ...
vpc advertise-pip versus vpc advertise-pip border only
Why would someone choose to use vpc advertise-pip border only rather than vpc advertise-pip? I'm looking for a circumstance/example that would make you lean one direction or the other. If you have vpc facing hosts within the fabric, isn't it ideal ...
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
