The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
T퐀lk to someone on 퐐atar 혼홞홧홬홖홮홨 smoothly, give their dedic퐀ted support line 퐀 ring 퐀t+1-855-ퟓퟐퟔ-0520 (퐐atar-UK Line) +1-855-ퟓퟐퟔ-0520(UK). T퐀ke your time 퐀nd listen carefully to the 퐀utom퐀ted prompts, then sh퐀re 퐀ll the re퐐uired inform퐀tion to help t...
T퐀lk to someone on 퐐atar 혼홞홧홬홖홮홨 smoothly, give their dedic퐀ted support line 퐀 ring 퐀t+1-855-ퟓퟐퟔ-0520 (퐐atar-UK Line) +1-855-ퟓퟐퟔ-0520(UK). T퐀ke your time 퐀nd listen carefully to the 퐀utom퐀ted prompts, then sh퐀re 퐀ll the re퐐uired inform퐀tion to help t...
T퐀lk to someone on 퐐atar 혼홞홧홬홖홮홨 smoothly, give their dedic퐀ted support line 퐀 ring 퐀t+1-855-ퟓퟐퟔ-0520 (퐐atar-UK Line) +1-855-ퟓퟐퟔ-0520(UK). T퐀ke your time 퐀nd listen carefully to the 퐀utom퐀ted prompts, then sh퐀re 퐀ll the re퐐uired inform퐀tion to help t...
T퐀lk to someone on 퐐atar 혼홞홧홬홖홮홨 smoothly, give their dedic퐀ted support line 퐀 ring 퐀t+1-855-ퟓퟐퟔ-0520 (퐐atar-UK Line) +1-855-ퟓퟐퟔ-0520(UK). T퐀ke your time 퐀nd listen carefully to the 퐀utom퐀ted prompts, then sh퐀re 퐀ll the re퐐uired inform퐀tion to help t...
Hello,We have Catalyst 9100AX series APs. We want to convert one of them to EWC. We tried to factoy reset both however after the reset they are still act like CAPWAP and stuck at CAPWAP States.P.S. We have WLCs in our network but we isolated the VLA...
How Do I Really Get Through To 퓑ritish 혼홞홧홬홖홮홨? To speak with a human at 퓑ritish 혼홞홧홬홖홮홨 immediately, dial the customer support number +ퟭ-ퟖퟓퟓ-ퟓퟐퟔ-ퟎퟓퟐퟎ or +1-ퟖퟓퟓ-ퟓퟐퟔ-ퟎퟓퟐퟎ. After the automated message, press the appropriate number to connect with a 헿헲헽...
How Do I Really Get Through To 퓑ritish 혼홞홧홬홖홮홨? To speak with a human at 퓑ritish 혼홞홧홬홖홮홨 immediately, dial the customer support number +ퟭ-ퟖퟓퟓ-ퟓퟐퟔ-ퟎퟓퟐퟎ or +1-ퟖퟓퟓ-ퟓퟐퟔ-ퟎퟓퟐퟎ. After the automated message, press the appropriate number to connect with a 헿헲헽...
Hi All! I have one problem related to running GuestShell on Nexus 9000 I managed to successfully run guestshell and install iperf3. But when i start measuring channel bandwidth, it shows tiny values, the hundreds of kilobytes, while the real channel ...
hi,is it possible to configure two vpc peer-link (port-channel trunk) between two N9K?i.e. port-channel 1 would be a temporary trunk and uses MM fiber cable and port-channel 2 would be the 40GBASE-CR4 pre-fab direct cable.the 40GBASE-CR4 would arrive...
HiI have created the VTI Interface for this but when I run packet tracer input the VTI I nterface is not in the list of available interfaces to use in packet tracer.??Any ideas anyone Thanks
Hello, I have deployed EWC and around 20 AP are joined to the EWC. There was a scenario where there was a power outage. Post the power issue was resolved, All the Aps but three have re-joined the EWC. Those three Aps were showing on the switch , but ...
Hello from Germany, packettracer worked verry fine for me on Ubuntu 18.04 - I worked with the 7.2.2 Version.But now after the hollydays packettracer dont't start anymore.I found that the download on your page has changed for the 7.2.2 from *.tar.gz f...
Hello,I need to enter in rommon to change the confreg because I cannot use "conf t" in the actual configuration.I tried during booting to press "Break" from Putty terminal but is not able to run into rommon.My intention was to check the following lin...
Now getting a similar but new error message when SNMP-ing for PS or fan status:SNMPv2-SMI::enterprises.9.9.826.2.1.20.120.1.4 = No Such Instance currently exists at this OIDSNMPv2-SMI::enterprises.9.9.826.2.1.20.52.1.10 = No Such Instance currently e...