The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
Hello, I deployed a new FTD 2110 on our company network and I'm seeing two different mac addresses on the switch port that the MGMT interface is connected to. I know that the one mac address is associated with the actual MGMT interface, but can anyon...
I am configuring ASA5516 from scratch and trying to find out the current recommended versions.Could you please advise?Curretly:ASA Software Version: 9.8(2)Firepower Extensible Operating System Version: 2.2(2.52)Device Manager Version: 7.9(2)152
Wired guests are not able to get out to internet, they can ping only at when payload is set to 1300 bytes or lower, this seems like an MTU issue, but its only effecting wired guest not wireless guest. Setup is a 9800 foreign on 17.9.5 code and 5520 a...
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
We are operating our vehicles remotely in the underground mines over Wi-Fi, the data load from the machine is constant around 30Mbit/s (yes, six to eight HD-cameras).When switching between APs we have noticed that we sometimes get a transmission gap ...
I'm using a 9200 device running IOS 17.9.I use a script and spreadsheet to generate my config file, which I then copy onto my devices via TFTP and then copy to the running config. Nothing unusual there. However, if I then ask the device to show me th...
Hi, We have some scripts that send a call redirect to a user's voicemail greeting and this works fine, using the call redirect step (destination = VM pilot, Called address reset to user's Ext.).The current set up from CUCM to Unity is SCCP, and I've ...
Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
The Cisco Document Team has posted an article. This document describes how to configure the Localized Identity Services Engine (ISE) Installation to reinstall or upgrade ISE. Know of something that needs documenting? Share a ne...
The Cisco Document Team has posted an article. This document describes the steps to troubleshoot Virtual Router Redundancy Protocol Version 3 (VRRPv3) with IPv6 in Nexus 9000. Know of something that needs documenting? Share a n...
The Cisco Document Team has posted an article. This document describes how to configure and verify Service Chaining to inspect traffic across different VRF. Know of something that needs documenting? Share a new document request...
Hi AllWe have a codec plus that refuses to go into standby . It will go into half sleep mode but as soon as that period has ended the system immediatly wakes back up. The unit does not have a control system connected and it does not have a content...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: