The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
はじめに Jabber for iPhone 等の VoIP クライアントでは、これまでApple Push Notification Service (APNs)を経由したPush通知によるコールの着信が行われていました。APNsはクラウド上にあるため、この着信方式を行うために Unified CM および VoIPクライアントはインターネットとの接続性を確保する必要がありました。Apple社では、インターネットとの接続が制限された環境で VoIP アプリが利用できるように Local Pus...
Hello everyone,There is a wireless network in use with AP2800 ME.I plan to link one more AP and change the SSID to a hidden SSID.The added AP operates normally and there is no connection problem. The IPs of all AP users connected to the controller AP...
Hi All. I would like to get your thoughts on the following issue i have been facing since implementing Dual ISP and failover for site-to-site vpn tunnels.Hub Site:ASA5515 using 9.6(4)42Spoke sites:Cisco ISRs using 15.1(4)M8, using voip services over ...
Hi All,I am newly building trustsec in my environment,trying to add one of the switch under trustsec. Have configured Trustsec settings and COA on the ISE for the switch and added the appropriate aaa commands , radius servers and cts commands.But sti...
Hi, how are you :). I have one question, about router Cisco 2911, and Juniper Netscreen 25, ver 5.4. I must start IP Sec tunnel between these two devices. I must use agressive mode, I saw this in configuration document. Question, how can I use agres...
I have upgraded cisco NCS-5504 router . Router was successfully upgraded but all the line cards are not showing. In platform command type is unknown and state is SW_Inactive.Regards Salman
Hello,At my home, I had an 8 port 2960G switch die after a power outage today. I replaced it with a ISR 1921 that has an 8 port ESM. It's been a very long time since I messed with configuring ESMs... My plan was to just copy over all of the switch...
hi,i'll be configuring a new N9K switch to replace a C9300.my question is, can i configure in advance the port-channel and vPC in the N9K even without the SFP inserted and fiber cables patched?just want to prepare the config so it will be a faster to...
You asked, we heard you! Introducing the ThousandEyes Support Community Capture the Flag event from April 23rd at 8 AM PST to April 29th at 5 PM PST. This month the ThousandEyes Community is offering two Capture the Flag missions in a single upcoming...
日頃より弊社製品をご利用頂き御礼申し上げます。この度、シスコシステムズ合同会社 カスタマーエクスペリエンス事業 カスタマーサクセス部門では、オンラインセミナー「つけっぱなしで使っていませんか?省エネと性能が両立できる無線 LAN 環境の作り方」を開催する運びとなりました。ご多忙のこととは存じますが ぜひご参加くださいますようご案内申し上げます。 ■日時:2024年4月24日(水)10:30-11:30■セミナー名:つけっぱなしで使っていませんか?省エネと性能が両立できる無線 LAN 環境の作り方...
How can I enhance the reputation of the ip reputation on https://talosintelligence.com from poor? Our emails are being blocked by numerous customers utilizing the Cisco email security platform. i submitted the ticket but still remain unchanged.
Hello when a BD subnet is advertised over an OSPF L3out, i'm seeing tha subnet as E2 external route with metric 20 on the router connectd to BL (VPC link). Why the subnet is shown as external and not internal OSPF route? Why the metric is 20 ? Regard...