The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
i cannot log in to the SNTC portal, i have the necessary roles that were applied last week (beyond the 24 hour period that is required for SNTC portal access), but each time i try to log in at services.cisco.com, I'm redirected back to the registrati...
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
Hallo All! What is the reason that when enabling Telemetry on C9300 Series Switches, only Application Name, Usage and Througput are shown? Switches configured with telemetry show only Application Visibility (Name and Throughput) in DNA center. Why is...
Já cursei o Conceitos Básicos de Redes e/ou CCNA1 e/ou CCNA2 em outra academia, posso participar do WRIT 2024 nas etapas seguintes? Sim. Pedimos anexar neste tópico o arquivo PDF, com o certificado do Skills for All ou Networking Academy do curso já ...
Has anyone tried adding multiple Algo 8182 SIP Strobe devices to their Cisco CUCM 12.5 PBX? I'd like the devices to activate on both "ring" and "in-use" events, but according to Algo that requires the "Subscribe/Notify" dialog event RFC 4235 on the P...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
My org has a single CUCM cluster with around 10k phones registered across 100+ buildings. We've been semi-regularly experiencing an issue that we've had trouble tracking down. Due to the nature of our deployment and the intermittent/difficult to repr...
The developer’s role in a greener future Developers can optimize software for Cisco devices to reduce their energy consumption. By writing efficient code, developers can minimize the processing power required to perform tasks, thereby lowering the en...
Dear all,I've set manually a specific port, in which have a non-Cisco WiFi 6 Access Point running, to provide 30W to make the PoE+ runs, but the AP itself didn't recgonize the power provided as PoE+.I've adjusted at web interface as well at CLI. Is t...
I have an ISR4431 router, and related setting:ip access-list standard toGCP10 permit 10.136.0.0 0.0.127.25520 permit 10.136.128.0 0.0.127.25530 permit 128.231.0.0 0.0.31.25540 permit 128.231.32.0 0.0.31.255!route-map toGCPmatch ip address toGCP!route...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: