Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1936299members
1261157discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

CAPWAP do not convert to EWC

Hello,We have Catalyst 9100AX series APs. We want to convert one of them to EWC. We tried to factoy reset both however after the reset they are still act like CAPWAP and stuck at  CAPWAP States.P.S. We have WLCs in our network but we isolated the VLA...

kdemir by • Level 1
  • 66 Views
  • 6 replies
  • 0 Helpful votes

How do I talk to someone on Singapore Air lines? ~Quick ~Support

 Talk to someone on Singapore and, if you need help, call their help line at Air  line【+ퟏ-ퟖퟓퟓ-ퟕퟑퟖ-ퟒퟕퟖퟏ】. Take your time and pay close attention to the automatic prompts. Next, provide them all the details they need to promptly resolve your issue. Spe...

Router for SRST function only

Hi, One of the our client want to use Different make WAN router (not cisco) for WAN connectivity. At the same time, they wanted the backup call manager option for their cisco phones. Can we use SRST router somewhere middle of the network without any ...

inhamit by • Level 1
  • 132 Views
  • 5 replies
  • 0 Helpful votes

Nexus9000 guestshell iperf3 values issue

Hi All! I have one problem related to running GuestShell on Nexus 9000 I managed to successfully run guestshell and install iperf3. But when i start measuring channel bandwidth, it shows tiny values, the hundreds of kilobytes, while the real channel ...

Use two vpc peer-link in Cisco N9K

hi,is it possible to configure two vpc peer-link (port-channel trunk) between two N9K?i.e. port-channel 1 would be a temporary trunk and uses MM fiber cable and port-channel 2 would be the 40GBASE-CR4 pre-fab direct cable.the 40GBASE-CR4 would arrive...

FTD Route based VPN

HiI have created the VTI Interface for this but when I run packet tracer input the VTI I nterface is not in the list of available interfaces to use in packet tracer.??Any ideas anyone Thanks

N3om by • Level 1
  • 98 Views
  • 5 replies
  • 1 Helpful votes

EWC not acquiring IP

Hello, I have deployed EWC and around 20 AP are joined to the EWC. There was a scenario where there was a power outage. Post the power issue was resolved, All the Aps but three have re-joined the EWC. Those three Aps were showing on the switch , but ...

Packet Tracer is not longer working on unbuntu 18.04

Hello from Germany, packettracer worked verry fine for me on Ubuntu 18.04 - I worked with the 7.2.2 Version.But now after the hollydays packettracer dont't start anymore.I found that the download on your page has changed for the 7.2.2 from *.tar.gz f...

Arik by • Level 1
  • 4633 Views
  • 13 replies
  • 5 Helpful votes

Resolved! Enter rommon NCS540 XR

Hello,I need to enter in rommon to change the confreg because I cannot use "conf t" in the actual configuration.I tried during booting to press "Break" from Putty terminal but is not able to run into rommon.My intention was to check the following lin...

kriskrs by • Level 1
  • 101 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Simulate DoS Attack in CML

Hallo,Is there a way to simulate a DoS attack in CML? I am doing a lab on CoPP and an attack is required but I am unable to generate this. Thanks.

Joy3 by • Level 1
  • 233 Views
  • 7 replies
  • 0 Helpful votes

Storing the hostname of the device into the variable from the yamlfile

Hi Team, In the n9k yaml file, I have devices section like this: devices:      device_1:       device_2:   In the script, I call this object as : self.parameters['uut'] = self.parameters['testbed'].devices['device_1'] I need to hardcode the hostname ...

o1 by • Cisco Employee
  • 62 Views
  • 1 replies
  • 0 Helpful votes
Load more