The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
When i discover a new switch with LAN-automation other switches, which are not directly connected to the specified interface are going into a queued status. Which means:Queued: The device is queued for later processing because it isn’t directly conne...
I have created a small network in packet tracer. See attached file. Ignore AS 300 and ISP as they are not configured. I am trying to communicate between AS 100 and 200. When I use show commands everything seems great. I see all routes distributed as ...
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
I have a DMVPN network with 4331 hub routers. Our HQ in Memphis has a hub on AT&T, and another on Lumen. Our New York hub is also a Lumen connection. All are 500Mb up/down. We have about 35 spokes around the US that peer to all 3 routers. BGP is the ...
Hi,FTD was added and to FMC and while configuring HA in FMC, deleted FTD from FMC.While trying to add again to same FMC, both primary and secondary FTD not getting registered in FMC.Could you please help on getting the FTD registered with FMC.
Just recently, our Windows Logon duo integration has been challenging users for 2FA every time they log in, even if it's just unlocking a session they just locked. We've changed no policies in DUO or GPO. Thinking it was maybe a software version thin...
What is best practice when it comes to AD connector(s)?If we were to have TWO AD connectors, is there a way to have it only fail over to the other connector if the active one went down? Rather than adding an additional connector on a separate server ...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
Hello.I'm working on a simple project and I have encountered an error where I cant access the HTTPS server via any terminal on the network. Any other post I have seen on the subject were either not relevant or I lacked sufficient knowledge to underst...
Hello, we recently had our cert for our VPN expire without notification via alert message. I've done some research in the FMC but can't find anything that monitors certificate expiration dates. A google search points toward REST API's of course but t...
a. I initiate a WebEx call on my phone (through WebEx App). Audio is working fine. I then plug in the USBc cable into my phone, CarPlay comes up on the car display. I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...
When we try to access to the CLI with Putty or other tool, after putting the credentials the next message shows up: *****PID file exists. But Adminshell service is not completely up.**********If adminshell is restarted manually, please wait for 15-20...
Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...
I am unable to get a sectera viper phone to register with call manager. I have it built as a common 7960 sccp phone profile. When it boots up it will pull an IP address but will not register. This is my first time working with one of these phones and...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: