Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1926343members
1238101discussions

Community Activity

SSID not discoverable by laptop in Packet Tracer

We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...

cmonte0247 by Community Member
  • 101 Views
  • 3 replies
  • 0 Helpful votes

BGP advertise route

I have an ISR4431 router, and related setting:ip access-list standard toGCP10 permit 10.136.0.0 0.0.127.25520 permit 10.136.128.0 0.0.127.25530 permit 128.231.0.0 0.0.31.25540 permit 128.231.32.0 0.0.31.255!route-map toGCPmatch ip address toGCP!route...

Cisco 9300X Static routes don't work to SVI Tunnels

NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...

CBD 2.7.1 Error while using a wildcard certificate

I'm running CBD2.7.1 and installed a public wildcard certificate.The following error is flashing on the top of the dashboard:"Server certificate does not contain your server address in Subject Alternative Name."Is this a bug when using wildcard certs...

SteveKC by Level 1
  • 1 Views
  • 0 replies
  • 0 Helpful votes

Cannot add FTD to FMC after deleting it from FMC

Hi,FTD was added and to FMC and while configuring HA in FMC, deleted FTD from FMC.While trying to add again to same FMC, both primary and secondary FTD not getting registered in FMC.Could you please help on getting the FTD registered with FMC.

riyas_tvm by Level 1
  • 65 Views
  • 4 replies
  • 0 Helpful votes

IPSec VPN Tunnel Lan-to-Lan decrypt count zero

Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...

El Rondo by Level 1
  • 214 Views
  • 13 replies
  • 0 Helpful votes

Snort3 not recognising SMTP/S but Snort2 did/does !?

I'm in the process of updating all our FTD's from Snort2 to Snort3 & almost everything appears to work, except SMTP/S email.Under Snort2 it shows in event logs as SMTP/S Client traffic type correctly, but when Snort3 is enabled, it does not recognise...

ida71 by Level 1
  • 111 Views
  • 5 replies
  • 0 Helpful votes

Err-disable on port 3850 -12xs switch

I'm a newbie but have a question: I upgraded my Palo (firewall ) and the port that the firewall is plugged into err-disables out. After doing a SHUT, NO SHUT the port came back to life. Any thoughts on why this happens? It seems to happen anytime I u...

AnyConnect Microsoft Teams & Skype Packet loss

Hi Guys,We're having some issues since deploying the AnyConnect VPN with users reporting poor call quality and packet loss on Microsoft Teams and over Skype both audio and video calls?Is there anything we can try or tweak on our ASA and AnyConnect se...

CUCM Dual Forking Capabilities

We are trying to accommodate an employee with hearing impairment so that they can use a TTY Display AND there is a compliance need for call recording.  Has anyone been able to overcome this obstacle?  We are running up against the inability for Call ...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: