The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
I have a C9200L switch running IOS 17.6.5. I am looking for the Command Reference page for the interface-level configuration command "switchport vlan mapping". I have looked through the indices of serveral IOS-XE 17.x Command Reference guides, but ...
We performed vulnerability scan on our C2960X switches and found the following message: Checks the supported MAC algorithms (client-to-server and server-to-client) of the remote SSH server. Currently weak MAC algorithms are defined as the followi...
Hi! As title suggests, Room Bar pro (or any newer generation device for that matter, that supports MTR software), is there any way for it to call into CMS meeting (OBTP and webRTC also acceptable)? CUstomer has native Cisco Meeting Server infrastruct...
Hello,I want to set up a IPSec IKEv2 VPN to a central ASA. On my side we have a cisco 897.First I tried a crypto map configuration. Didn't work because the IKEv2 SA goes UP and immediately goes DOWN with the error message "IKEv2:(SESSION ID = 1,SA ID...
Dear All,I am planning to join a new Domain to my Cisco ISE enviroment.Now I already have a MS Domain Joined, and I use ISE to perform AAA, on the Devices and Users.I am using TEAP with EAP-TLS as inner method. It works well.But when I have added a n...
This is the command i type: r2(config)#Track 1 int g0/0/0 line-protocol and it gives me an invalid input at the track part. is there a different configuration mode I need to be in or is it unsupported? I tried this on both 4000 series routers and a 2...
Hey everyone, I need to get the IP Address and The Hostname into 2 different variables. I've got something like this: event manager applet AddHostnameToIPHostevent syslog pattern "DHCPD: Updating 'PTR' RR (.*) -> '(.*).tobi.local.'"action 1.0 syslog ...
Hello everyone,We would like to use our “old” C2960X devices, which we have in large numbers, to connect simple devices such as printers or PCs that do not require PoE. The goal is to use SGT for these devices. I have already read that it is not poss...
My name is Zake and i want to ask how to setting severity in Cisco Estream, i use Cisco Firepower 3120 and want ingest log to Azure Sentinel. I was successfull to ingest log but there is too much log i got, when i see there is too much information se...
The user computer switches to voice vlan but the port configuration has both access vlan and voice vlan.Avaya ip phone switches to voice vlan.The user computer also switches to voice vlan.What could be the cause of this problem?Port configuration swi...
I want to use netconf to get status from C9800. module: Cisco-IOS-XE-wireless-access-point-oper +--ro access-point-oper-data +--ro ap-radio-audit-info* [wtp-mac radio-slot-id]
HejI have performed a local install, but I can not login to the GUI using admin/admin.I can login to CLI with "ncs_cli -C -u admin" , but when I do "show run", all I see is snmp configuration on the device. I can not see AAA or configure it.cisco@Ubu...
Hi everyone, I want to upload the startup-config to real router via tftpd64 in vmware windows server. Windows server and ESR6300 are under the same network. But ESR6300 can ping windows server only from mgmt vrf. Through global router ESR6300 can'...
Hi,I want to secure one LAN port of my CBS350-48P switch. It is located to PoE camera outside the building.It would be great to shut down the port, if another device is put into this port.How can this be solved?Best regards,Heinz
Can someone please share steps and documentation for the VPC configuration in Cisco ACI Leaf switch. Any Pre-configuration Checks? Model- CiscoN9K-C9332C