Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1926464members
1238341discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Redistribution of OSPF through BGP .pkt stumped

I have created a small network in packet tracer. See attached file. Ignore AS 300 and ISP as they are not configured. I am trying to communicate between AS 100 and 200. When I use show commands everything seems great. I see all routes distributed as ...

msgrayII by • Level 1
  • 6 Views
  • 0 replies
  • 0 Helpful votes

Resolved! DMVPN issue with 800 series routers

I have a DMVPN network with 4331 hub routers. Our HQ in Memphis has a hub on AT&T, and another on Lumen. Our New York hub is also a Lumen connection. All are 500Mb up/down. We have about 35 spokes around the US that peer to all 3 routers. BGP is the ...

Cannot add FTD to FMC after deleting it from FMC

Hi,FTD was added and to FMC and while configuring HA in FMC, deleted FTD from FMC.While trying to add again to same FMC, both primary and secondary FTD not getting registered in FMC.Could you please help on getting the FTD registered with FMC.

riyas_tvm by • Level 1
  • 89 Views
  • 5 replies
  • 0 Helpful votes

Windows Logon Excessive 2FA Challenges

Just recently, our Windows Logon duo integration has been challenging users for 2FA every time they log in, even if it's just unlocking a session they just locked. We've changed no policies in DUO or GPO. Thinking it was maybe a software version thin...

mattford by • Level 1
  • 164 Views
  • 5 replies
  • 0 Helpful votes

Umbrella Redundancy for AD Connector

What is best practice when it comes to AD connector(s)?If we were to have TWO AD connectors, is there a way to have it only fail over to the other connector if the active one went down? Rather than adding an additional connector on a separate server ...

bnuxoll by • Level 1
  • 39 Views
  • 1 replies
  • 0 Helpful votes

Roteamento

Saudações, comunidade!Queria saber de vocês, qual é o vosso protocolo de roteamento favorito..? eu uso bastante o OSPF

L2VPN Over GRE

Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...

Resolved! packet tracer "Server Reset Connection" error

Hello.I'm working on a simple project and I have encountered an error where I cant access the HTTPS server via any terminal on the network. Any other post I have seen on the subject were either not relevant or I lacked sufficient knowledge to underst...

jenia69 by • Level 1
  • 18322 Views
  • 7 replies
  • 1 Helpful votes

WebEx Audio not working on CarPlay

a. I initiate a WebEx call on my phone (through WebEx App).  Audio is working fine.  I then plug in the USBc cable into my phone, CarPlay comes up on the car display.  I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...

bnsrini by • Level 1
  • 271 Views
  • 5 replies
  • 0 Helpful votes

Unable to get console access on switch 3850 - Blank terminal

Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...

mrjelly by • Level 1
  • 112 Views
  • 7 replies
  • 0 Helpful votes

GD Secter'a vIPer phone

I am unable to get a sectera viper phone to register with call manager. I have it built as a common 7960 sccp phone profile. When it boots up it will pull an IP address but will not register. This is my first time working with one of these phones and...

helmkamp01 by • Level 1
  • 7000 Views
  • 10 replies
  • 0 Helpful votes
Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: