The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello,We are having ISE for EAP/TACACS authentication and, hosted internally in our datacenter.Now we have configured BYOD captive portal that tied to AZURE SAML authentication, the current captive portal redirect URL from ISE has prepended the node ...
hello. I understand that Connected routing has an AD value of 0. The IP bands on the 1st and 2nd floors are different. 1st floor: 1.1.1.0/242nd floor: 2.2.2.0/24 There are two firewalls on top of the backbone. The band will be 3.3.3.0/24. If you conf...
Hi All, I'm trying to establish a SIP trunk to an ITSP using TLS and SRTP. We think we have done all the trust point stuff and TLS seems to be OK. However, I'll a little lost on the SRTP. Looking at several guides looks like a few different methods. ...
I have a trunk between cucm 6.1.5 and asterisk but when a call is made from cucm to asterisk it disconnects immediately it is picked (call from asterisk to cucm is ok). But it is working with cucm 10.5. I try route call from cucm 6.1.5 to 10.5 then c...
Good morning all!I am working on a project on our SD-WAN. I am new to SDWAN and vManage and was asked to look into possibly scripting some packet captured over a period of time. Our SDWAN consists of several IR1101's and they can only be managed via ...
Newbie CUCM user -- Is it possible to set individual ATA not to dial 9 when dialing out. We do not want to globally change the dial 9 for outside call rule just certain extensions
Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...
Hello everybody, our customer is using the FMCv rel. 7.2.5.1 and many FTDs.After de-register/re-register the FMC in the Smart Software Manger because another error message four devices (7.0.1 & 7.0.5) fourdevices show the error: Threat Data Updates o...
I'm having problems setting up my home network using Cisco2921 for the first time. It has the basic licenses only. Below is the running config followed by my adapter settings. Any assistance would be greatly appreciated. Thank you.Current configurati...
Hi Guys, As we know, there is option in Cisco 5520 WLC to mannualy disable any Mac addresses of user to deny network access to him. Is there any disable mac address option in Cisco 9800 WLC?
Sage 50 support encompass a wide range of offerings designed to assist businesses at every stage of their software implementation and usage lifecycle. These services are tailored to meet the diverse needs of organizations, ranging from small startups...
Hello, We have a user that has misplaced the USB Y cable RJ9/RJ11 that came with the 561 multibase. They use that cable to connect to a 7841 phone. I do not see that cable listed a spare to purchase in the data sheet or in CCW. Any advice on what...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
Foro Ask Me Anything (del 18 al 26 de abril de 2024) Este foro está dedicado a las preguntas relacionadas con el webinar "NXOS Mejores Prácticas para Upgrade", del pasado jueves 18 de abril de 2024. Revisen la grabación, envíenos sus dudas o comenta...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: