Brandon Svec

Member Since: Nov 11, 2008

English
Brandon Svec's Activity on Cisco Support Community
Currently displaying 50 results

Brandon Svec has commented on Switching

1 day 8 hours ago
CLI guide indicates, yes.  I imagine it would need to be in L3 mode.https...

Brandon Svec has commented on How to access web GUI on SG500X-24 after setting up VLANs

2 days 10 hours ago
So switch is not in L3 mode, right?  In general you just need to have a...

Brandon Svec has commented on Connect old catalist 1900 to small businness SG500

2 days 10 hours ago
I'm only guessing, but I would try full duplex on the 1900.  I would...

Brandon Svec has commented on cisco SG300-28P gigabit PoE managed switch

2 days 10 hours ago
The easiest way is to use a regular Ethernet cable connected to any port and...

Brandon Svec has commented on Help needed for c3550 swicth

2 days 10 hours ago
It may be counterfeit?  You said after reset it would come up for a short...

Brandon Svec has commented on SG300: able to route by connection?

3 days 4 hours ago
I looked at your config again and I can't see obviously what's wrong,...

Brandon Svec has commented on SG300: able to route by connection?

3 days 4 hours ago
In L3 mode the switch becomes a router and will route by default.  do sh...

Brandon Svec has commented on SG300: able to route by connection?

3 days 5 hours ago
If your host devices use the VLAN interface IP as their gateway then inter-vlan...

Brandon Svec has commented on Help needed for c3550 swicth

3 days 8 hours ago
It sounds like a hardware failure and it will need to be replaced.  How...

Brandon Svec has commented on Inter VLan routing on SG300-52

3 days 11 hours ago
Strange.  The only thing somewhat unique (compared to my common configs)...

Brandon Svec has commented on Inter VLan routing on SG300-52

3 days 22 hours ago
Here my observations and ideas-- First, all you VLANs in this config are tagged...

Brandon Svec has commented on Help needed for c3550 swicth

1 week 10 hours ago
Status is amber as well?  This may be a fatal error, unfortunately.  ...

Brandon Svec has commented on SG300 Switch - One-Way Access to subnets

1 week 1 day ago
I'm going to guess the default gateway is not appropriate on those devices...

Brandon Svec has commented on Sg500x - dhcp option 150

1 week 3 days ago
I believe this is the command you are looking for, but it is not clear if it...

Brandon Svec has commented on Sg500x - dhcp option 150

1 week 3 days ago
What version firmware and are you in L3 mode?  I think option 150, 66 and...

Brandon Svec has commented on SG300-10PP and 10MPP cannot provide POE+

1 week 3 days ago
The data sheet states both models support 802.3at PoE+ http://www....

Brandon Svec has commented on Meraki AP management through MX security appliance

1 week 6 days ago
The MX and the MR are technically setup as different networks managed under the...

Brandon Svec has commented on Can Cisco Small Business switches drive ICS cabling?

2 weeks 1 day ago
Pins 1,2,3 and 6 are what you need, but don't expect much out of old cable...

Brandon Svec has commented on Assign ip address to a VLAN

2 weeks 2 days ago
Maybe this helps? https://supportforums.cisco.com/discussion/11579836/...

Brandon Svec has commented on Assign ip address to a VLAN

2 weeks 2 days ago
Yes, you can still do router on a stick, but that means you do L3 routing on...

Brandon Svec has commented on Assign ip address to a VLAN

2 weeks 3 days ago
I don't think the SG200 is a layer 3 switch.  SG300 or SG500 if you...

Brandon Svec has commented on SG200-26P makes randomly reboot IP phones SPA504

3 weeks 1 day ago
What does your switch config look like?  Ae you using auto smartports and...

Brandon Svec has commented on Multiple (7) Cisco SG300 switches connected?

1 month 5 days ago
Is the x in your diagram intended to be the same in all cases?  So OBFN (...

Brandon Svec has commented on New to Cisco SG300-10 as well as L3 networking, IPv4 Interfaces & Routes

1 month 5 days ago
Yes, you have the general idea.  I couple tips:The switches are L2 by...

Brandon Svec has commented on Cascading two SG220-26 switches

1 month 2 weeks ago
I see.  Yes you can do this with any switches, really.  One bit of...

Brandon Svec has commented on Trunk Configuration missing after rebooting the SG-500-28 switch

1 month 2 weeks ago
I have seen this problem myself and other strange issues to do with auto...

Brandon Svec has commented on Cascading two SG220-26 switches

1 month 2 weeks ago
These switches do not stack, you need to go to the Sx500 series for stacking...

Brandon Svec has commented on ESW-520-24P and a power outage

2 months 3 days ago
You might also find an analog phone to bring in and try connecting it directly...

Brandon Svec has commented on ESW-520-24P and a power outage

2 months 4 days ago
Do you have analog/FXO lines?  My guess would be those, but if the trouble...

Brandon Svec has commented on Deny access to any port on the switch by MAC adress

2 months 1 week ago
Yes, it should be possible with MAC based ACL.  Here is a guide that steps...

Brandon Svec has commented on Release Notes for 1.4.1

2 months 2 weeks ago
and there they are: http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/...

Brandon Svec has commented on Release Notes for 1.4.1

2 months 3 weeks ago
I use this site to monitor for changes on Cisco pages among others: https...

Brandon Svec has commented on SG 300 - Connection closed by server: Server reached maximum number of simultaneous connections

2 months 3 weeks ago
I would do show users via your console connection so you can see if/who is...

Brandon Svec has commented on SG300 28PP VLANs and DHCP

2 months 3 weeks ago
My opinion is that doesn't make any difference where you put DHCP.  It...

Brandon Svec has commented on PORT VLAN MEMBERSHIP

2 months 4 weeks ago
Glad to hear that.Feel free to rate my post and mark as correct if everything...

Brandon Svec has commented on SPAN Port Monitoring Setup

3 months 3 days ago
I would suggest moving this post here: https://supportforums.cisco.com/...

Brandon Svec has commented on SG300 as DHCP server on private vlan is not working

3 months 5 days ago
As I understand DHCP server is only supported in L3 mode.  I think...

Brandon Svec has commented on Multiple Default Routs With Multiple Vlans SG500 - 48

3 months 1 week ago
I agree with cchamorr, but can't you keep ISP connection and users in same...

Brandon Svec has commented on Running CME on second hand 2811

3 months 1 week ago
This should help: http://www.cisco.com/c/en/us/support/unified-...

Brandon Svec has commented on Cisco 220-48P

3 months 2 weeks ago
The data sheet states:Switches support 802.3af, 802.3at, and Cisco pre-standard...

Brandon Svec has commented on Cannot access SPE2000 web console

3 months 3 weeks ago
Also, there is a super secret unsupported CLI on these switches:To access the...

Brandon Svec has commented on Cannot access SPE2000 web console

3 months 3 weeks ago
You mean SFE2000 switch, right?  If so it has a console port.  Why...

Brandon Svec has commented on New setup of SG300 switch for voice and data

3 months 3 weeks ago
An ATA is supposed to get an internal IP the same way an IP phone does.  ...

Brandon Svec has commented on Firmware upgrade SG200-26P from oldest version.

3 months 3 weeks ago
I am feeling invisible here ;)  I think my response is correct.  From...

Brandon Svec has commented on Voice VLAN Help Please

3 months 3 weeks ago
can you try show lldp neighbors when you have a phone plugged in?  It...

Brandon Svec has commented on Voice VLAN Help Please

3 months 3 weeks ago
Here is an example of part of a working switch config with Zultys phones where...

Brandon Svec has commented on Firmware upgrade SG200-26P from oldest version.

3 months 3 weeks ago
You need to upgrade to 1.3.5 or 1.3.7 before proceeding to 1.4.0.88.  The...

Brandon Svec has commented on Voice VLAN Help Please

3 months 3 weeks ago
What kind of phones?  When you turn on auto VLAN, by default the switch...

Brandon Svec has commented on Routing between 2 switches layer 3

3 months 3 weeks ago
Routing between VLANs on a L3 switch is actually the default.  You have to...

Brandon Svec has commented on PORT VLAN MEMBERSHIP

3 months 3 weeks ago
global command is: macro auto disabledper port command is: no macro...

Bio

I have 20 years of voice and data technical experience. Over the years I have obtained over 30 technical certifications on a broad range of products from Cisco , NEC, Nortel, Polycom, ShoreTel, Zultys, Meraki and others.
At Expanets, previously the largest interconnect company in the U.S., I was promoted from field technician to Service Manager and then to Engineering Manager for their Northern California Operations. At Team One Solutions I am a partner and responsible for all voice and data system pre-sale engineering and design as well as post-sale engineering support and professional services.








  • Community Spotlight Award

    Small Business, April 2015





  • Community Spotlight Award

    Small Business September 2013









Brandon Svec's Stats

Points455
Discussion started 28
Answers marked as Correct 41
Endorsed 6
Content Rated 254
Website: