burleyman

Member Since: Jul 19, 2002

English
burleyman's Activity on Cisco Support Community
Currently displaying 20 results

burleyman has created Passing traffic over wirless work group bridge

2 days 12 hours ago
I have the following setup and need help with passing traffic over the wireless...

burleyman has commented on Most DMVPN sites down after ASA upgrade

3 days 12 hours ago
I am a little confused on this, the title says DMVPN on the ASA, but ASA's do...

burleyman has commented on connection between HQ and 2 remote sites

5 days 19 hours ago
Yeah, I did not quite understand the wording on the line "note : i've tried...

burleyman has commented on connection between HQ and 2 remote sites

6 days 20 hours ago
The 37.20.20.20 is the public IP address of the HQ router, al least that is...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 2 days ago
Thanks for your help. Mike

burleyman has commented on connection between HQ and 2 remote sites

1 week 3 days ago
This should work. You do not need static IP addresses on the hub routers. On...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 4 days ago
It worked swimmingly, thank you for your help. I do have a some questions.......

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 4 days ago
Thank you. I will give it a go. Mike

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Switch#tclshSwitch(tcl)#puts [open "flash:shut_port.tcl" w+] "set ports [lindex...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Ok I will see if I can figure it out. I have never programmed TcL but I will...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Just tested and it does not work, am I missing something?

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Sorry I had no in the above post. This is what I was entering. kron policy-...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Here is what I am going to test now. kron policy-list policy_IntShutcli config...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Yes, that is where I found this. I got mixed up on TcL and EEM, sorry very new...

burleyman has commented on TcL Script to shut down port on a time schedule

1 week 5 days ago
Here is what I was going to try that I found. event manager applet shutdown-...

burleyman has created TcL Script to shut down port on a time schedule

1 week 5 days ago
Is there a way to have a TcL script shut and no shut ports on a schedule? for...

burleyman has commented on "no exec" command keeps returning, Cisco 1921 universalk9 15.4(3)M5

1 month 2 weeks ago
If you want to disable it you can. 1921Router(config)#line 2 1921Router(...

burleyman has commented on "no exec" command keeps returning, Cisco 1921 universalk9 15.4(3)M5

1 month 2 weeks ago
You can't delete "Line 2" it is automatically created on ISR G2 platforms and...

burleyman has commented on Wireless bridge configuration help

1 month 2 weeks ago
Thanks for the information. Very helpful and I almost got this working. Just...

burleyman has created Wireless bridge configuration help

2 months 1 day ago
I have a Cisco IR829GW router with an embedded wireless AP and here is what I...

Bio










  • Community Spotlight Award

    Members Choice February 2012









burleyman's Stats

Points1551
Discussion started 201
Answers marked as Correct 75
Endorsed 1
Content Rated 409