Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1927017members
1239412discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

WLC, SSO and OEAP

Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...

nat,.JPG
Moudar by • VIP
  • 72 Views
  • 2 replies
  • 0 Helpful votes

Tracking network speed

Hi thereI am assigned to check the issues with this attached network and have managed to remove some hups and redesign the network to what it is now. there were no vlans and it has been configured. the issue is that the internet speed is extremely sl...

Resolved! Not able to go into Rommon

Hello, I have used Cisco 1921, and we forgot its login and password. I am trying to go into rommode for password recovery but am not able to. During router boot-up process I am using special command > Break to force rommode , router shows " Readonly...

Internal batteries

Does the Catalyst 2960-X or 350-P network switches have internal coin cell batteries to retain memory or clock settings? If so, what is the part number of this battery. Alternatively do you have a safety compliance document for the battery which allo...

Network Architecture

Hello Everyone,I'm novice to networking. And below is the requirement I'm trying to figure out. Any leads would be greatly appreciated"You are working as an IT architect for a new startup business that grew faster than expected. they expanded to oper...

Ram253 by • Level 1
  • 3 Views
  • 0 replies
  • 0 Helpful votes

connetion events in FMC

Hi Dears,in our company we have FMC\FTD but the logs (connection event) were saved for almost 1 week back only.i have been checked the limitation as the below tableConnection eventsSecurity Intelligence events50 million (FMC Virtual, FMC750) 100 mill...

khaled-jd by • Level 1
  • 8 Views
  • 0 replies
  • 0 Helpful votes

ISE DNS health check showing warning

Hi all,I have a four new standalone nodes which will be going into a cluster, I am seeing two nodes have a DNS warning. All nodes are located in the same caI can ping both DNS servers .21 and .22 and nslookup up works to resolve its own IPWhy are two...

NetworkMonkey101_0-1713418948817.png

mac flapping

Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...

AP Alarm

 What is the meaning of this Alert and what can I do to mitigate this. (for Unified Access Points)Message: '802.11a/n' interface of AP 'XXX' associated to controller 'XXXX)' is down. Reason: Radio reset due to (56) Radio channel set

collrbbrt by • Level 1
  • 66 Views
  • 1 replies
  • 0 Helpful votes
Load more
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: