geraghtyconor

Member Since: Oct 30, 2007

English
geraghtyconor commented on CCME stripping too much!! in IP Telephony 2 years ago

I fixed it myself - should I give myself points??DS-01(config)#dial-peer voice 1010 potsDS-01(...

geraghtyconor commented on Cisco Unified CCX Premium - 7.0(1)SR05_Build504 - Supervisor broadcast message in Contact Center 2 years ago

Cheers Aaron.configs all match - same subnet - perhaps a resource issue??!!

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

Success!!THANK YOU AMINE!!!ephone  1 mac-address xxx.yyyy.zzzz.aaaa type 7940 button  1:1...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

+3.5!We do use custom softkeys...ephone-template  2 service phone ehookEnable 1 user-locale 1...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

I think Amine Nouasri's answer might be the right direction.i'm try to configure a...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

Nope!So! I dont need to perform any configuration on the button I wish to apply the change!!I have...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

I apologise!Alas - no button still!! i think we're half way there - perhaps I need ... button 2:(...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

ephone 1speed-dial 1 01698611020 label 01698611020And that will produce the result exactly per the...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

You're not reading my request.press line 2 (see pic) and it automatically dials 01698.........how...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

EXACTLY!how did they make a line a speed dial?

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

No alternatives will be considered - she's seen it before and wants it on her new system - THE END!...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

cheers....My customer want one of the line buttons on the right-hand-side of the 7942 to dial...

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

ephone-dn 1button 2:91001/91001/ /0123456789/?????going to test it now................

geraghtyconor commented on programme 'second line' softkey as single number speed dial on 7942 (CCME) in IP Telephony 3 years ago

Yip - I did that. Got rejected.Problem 1 = Call Center manager from hellProblem 2 = Manager has...

geraghtyconor commented on Upgrade Nexus 7010 from 4.2(4) to 6.1(1) in LAN, Switching and Routing 3 years ago

Thank you.What about EPLD??Will in need to double upgrade that also? (i.e. version 4 to 5 to 6?)  ...

geraghtyconor commented on route pattern format question in IP Telephony 4 years ago

It refers to a SIP trunk (a polycom VC sits at the end of it)it can be dialled from the PSTN or...

geraghtyconor commented on Policy based NAT to share 1 public between to two internal servers in Firewalling 4 years ago

I need two-way communications (in and out). I am really struggling with the difference between;...

geraghtyconor commented on Policy NAT for AH/ESP and tcp in Firewalling 4 years ago

!I have used global (outside) 1 and 2 already. This is what I was thinking.!access-list policyNAT-...

geraghtyconor commented on Policy NAT for AH/ESP and tcp in Firewalling 4 years ago

I want to use 1 public IP address NATTed to 2 internal private IP addresses.1: NAT an IPSEC circuit...

geraghtyconor commented on Policy NAT for AH/ESP and tcp in Firewalling 4 years ago

I.e. I want to use one of my Public facing IP addresses to accept two circuits for static NAT1 To...

geraghtyconor commented on ASA Firewall interface security levels and access-lists in Firewalling 4 years ago

Thank you.Therefore, hence; Security level is priority??A: Unless security 0 (x) = nothing passes...

geraghtyconor commented on I wish to block P2p & IM but, I also deny Yahoo & Google web sites in Firewalling 8 years ago

Thx BUT - that's the link I inserted above!! This procedure ASLO denies my users access to yahoo.co...

geraghtyconor commented on 871 with IPSEC-i need to static NAT my DCs to internet but still use ipsec in VPN 8 years ago

Woops Typo "wack on an ACCESS list" (not address list).i.e.Static Nat them for site-to-site comms...

geraghtyconor commented on 871 with IPSEC-i need to static NAT my DCs to internet but still use ipsec in VPN 8 years ago

Alas no - I tried a ROUTE-MAP statement per above - no joy. Is it a limitation with the 871 router...

geraghtyconor commented on HELP! password recovery for pix 501 in Firewalling 8 years ago

Rest of packetsFrame 1049 (89 bytes on wire, 89 bytes captured)Ethernet II, Src: Dell_97:be:b8 (00:...

geraghtyconor commented on HELP! password recovery for pix 501 in Firewalling 8 years ago

No, this does not work - i get the same. In fact i tftp the .bin file and then get an error - my...

Bio












geraghtyconor's Stats

Points0
Discussion started 21
Answers marked as Correct 0
Endorsed 0
Content Rated 20