Mohammad Ali

Member Since: Jun 30, 2010

User Badges:
  • Silver, 250 points or more

English
Mohammad Ali commented on MST and Rapid PVST in LAN, Switching and Routing 3 months ago

Long story short my company acquired another company and they just started throwing Dell switches...

Mohammad Ali commented on Problems Creating New Interface On 2504 in Getting Started with Wireless 5 months ago

Can you draw out your connectivity.  Because you should be able to get this going easily.  Do you...

Mohammad Ali commented on Wireless Site Survey - TX Power of wifi devices in Getting Started with Wireless 5 months ago

Which barcode scanner are you using Motorola's?  If you are, their transmitters output power is...

Mohammad Ali commented on Unable to console to aironet 1041N in Getting Started with Wireless 5 months ago

And you are using a Cisco Console cable going to the Serial port on your desktop?

Mohammad Ali commented on WLC FlexConnect in Getting Started with Wireless 5 months ago

It all depends on your design and need I believe.  I worked in an environment where we did both...

Mohammad Ali commented on 3602i "dropping" on iPhones in Getting Started with Wireless 6 months ago

Any recent change in the wireless environment?  Like more interference perhaps in the 2.5GHz band...

Mohammad Ali commented on Heat map Site Survey with both 2.4 and 5 GHz radios on? in Getting Started with Wireless 6 months ago

I don't really see any issues with that.  I have done 5GHz surveys with dual band AP's.  I just...

Mohammad Ali commented on In case two DHCP pool confined on both routerA/B. in LAN, Switching and Routing 6 months ago

What Mark said is right.  I however had a need to do get something like this done.  Had two routers...

Mohammad Ali commented on wireless SSID limitation in Getting Started with Wireless 6 months ago

Are you using a Cisco WLC?

Mohammad Ali commented on Student Support with Wireless Access Point 2602e in Getting Started with Wireless 6 months ago

If you just purchased this from an authorized seller try contacting Cisco and see if they will give...

Mohammad Ali commented on Activating Inactive Licenses on WLC 5508 in Getting Started with Wireless 6 months ago

Actually looks like initially your controller was purchased with a base AP license of 12 access...

Mohammad Ali commented on Unable to Access AP neither via telnet nor via GUI. in Getting Started with Wireless 6 months ago

Do you see an IP on the DHCP server for this AP?  Can you ping it?  Or if you change the port to an...

Mohammad Ali commented on Cisco 3700i access points on Meraki switch in Getting Started with Wireless 6 months ago

You are welcome, here is another screen shot that shows you how to get to the DHCP settings.

Mohammad Ali commented on Cisco 3700i access points on Meraki switch in Getting Started with Wireless 6 months ago

I'm going to assume you have a setup somewhat similar to what is in the diagram.  6800 has the SVI...

Mohammad Ali commented on Cisco Virtual Wireless controller and wism in Getting Started with Wireless 6 months ago

You should be able to use another WLC virtual WLC for the new access points.  Getting the same SSID...

Mohammad Ali commented on WLC WebAuth - Multiple Web login pages? in Getting Started with Wireless 6 months ago

No it should not interfere with the existing page.  I had to configure once something like this:...

Mohammad Ali commented on Cisco 3700i access points on Meraki switch in Getting Started with Wireless 6 months ago

I also have a Cisco AP/WLC with a Meraki Switch/Firewall setup and it is working fine.  In my case...

Mohammad Ali commented on Multiple SSIDs: Interfaces or FlexConnect VLAN Mapping in Getting Started with Wireless 6 months ago

I drew a quick summary of this, hope this helps.  Ask any questions you might have.  You would want...

Mohammad Ali commented on Access Point not Joining to 2504 WLC through Internal DHCP in Getting Started with Wireless 6 months ago

If you console into the AP check out the logs and see what you are getting.  Logs on the AP are...

Mohammad Ali commented on Routing protocol between two 7K's in LAN, Switching and Routing 7 months ago

Thank you for the response and apologies for the late reply.  Here is the BGP config if it helps...

Mohammad Ali commented on Warehause WiFi in Getting Started with Wireless 7 months ago

You also need to figure out what kind of clients you have and what requirements they have.  I have...

Mohammad Ali commented on Routing protocol between two 7K's in LAN, Switching and Routing 7 months ago

Thank you Richard that is what I am normally used to i.e; running eBGP externally and OSPF...

Mohammad Ali commented on To configure timeout for Guest Network in Mobility Express in Getting Started with Wireless 10 months ago

Not sure if you got your answer or not but this should help http://www.cisco.com/c/en/us/td/docs/...

Mohammad Ali commented on Wireless controller and ADSL guest wifi in Getting Started with Wireless 11 months ago

You are welcome I understand that is what I meant.  1- you get DSL circuits at each location 2- you...

Mohammad Ali commented on Wireless controller and ADSL guest wifi in Getting Started with Wireless 11 months ago

Ok so it would be a good idea to utilize AP groups for each site.  Gives you some organization and...

Mohammad Ali commented on Flexconnect across two countries in Getting Started with Wireless 11 months ago

So yeah you might want to create AP groups and add AP's into sites group. It would not matter if...

Mohammad Ali commented on wireless controller in Getting Started with Wireless 11 months ago

If you are doing SSO with 5508, one of your WLC will require a 50 license count.  Second one will...

Mohammad Ali commented on Flexconnect across two countries in Getting Started with Wireless 11 months ago

You should be able to, I don't see why not.  What is the WAN link between the two sites?  Is there...

Mohammad Ali commented on Wireless controller and ADSL guest wifi in Getting Started with Wireless 11 months ago

Are you using AP Groups for each site, also are the AP's in FlexConnect mode or local mode?

Mohammad Ali commented on Client Packet capture question in Getting Started with Wireless 12 months ago

Ah gotcha thank you for your reply.  Would it make a difference if I trunk the port where AP is...

Mohammad Ali commented on Cisco 2504 - setup 2 wlan, one allow internet traffic/one without in Getting Started with Wireless 12 months ago

Your management network is huge do you have that many network devices in there or are you using it...

Mohammad Ali commented on Cisco 2504 - setup 2 wlan, one allow internet traffic/one without in Getting Started with Wireless 12 months ago

Under Controller and Interfaces you are saying you are unable to create another VLAN interface? You...

Mohammad Ali commented on 4321 QoS Question in WAN, Routing and Switching 1 year ago

Thank you one last question, when you say license limited are you talking about the throughput ?

Mohammad Ali commented on 4321 QoS Question in WAN, Routing and Switching 1 year ago

Got it thank you, so I guess with IOS XE I will need to put some number in there and 8000bps is the...

Mohammad Ali commented on One Network & Two ISP , redundancy at WAN level in Small Business Support Community 1 year ago

You sure can do it.  Can you show us the topology of what you have and what kind of equipment are...

Mohammad Ali commented on Cisco Access Point for Coolers in Getting Started with Wireless 1 year ago

I know it has been a while I asked this question but wanted to update the thread so it my help...

Mohammad Ali commented on Cisco Access Point for Coolers in Getting Started with Wireless 1 year ago

Thank you Scott, I have done one smaller area like that with a patch antenna.  Do you use the same...

Mohammad Ali commented on 3rd party SSL cert and two WLC's in Getting Started with Wireless 1 year ago

Thank you Brett and Scott I'd love to be able to do that but here is what confusing me a bit. ...

Mohammad Ali commented on 3rd party SSL cert and two WLC's in Getting Started with Wireless 1 year ago

Thank you Brett.  So this WLC has a different host name as I am doing Flex Connect on this one and...

Mohammad Ali commented on WLC5508 and 3rd party SSL cert in Getting Started with Wireless 1 year ago

Thank you Scott.

Mohammad Ali commented on Cisco Autonomous AP EAP Authentication not working in Getting Started with Wireless 1 year ago

Already checked that, this is not even hitting the ACS server as I mentioned. 

Mohammad Ali commented on Wireless client authentication issue with ACS in Getting Started with Wireless 1 year ago

Here is the basic related config.  I don't even see any logs on the ACS server from this AP or any...

Mohammad Ali commented on Fast busy outbound caling pots lines in IP Telephony 1 year ago

It was something pretty lame lol.  I forgot to add the Route Group to the Pool dang it lol.  Haven'...

Mohammad Ali commented on Fast busy outbound caling pots lines in IP Telephony 1 year ago

System version: 8.6.2.22900-9MGCP

Mohammad Ali commented on ACS 5.5 and WLC 5508 Management Access via RADIUS Auth in AAA, Identity and NAC 1 year ago

No problem same here :), thank you for your help.  So instead of RADIUS I am trying to see if I can...

Mohammad Ali commented on ACS 5.5 and WLC 5508 Management Access via RADIUS Auth in AAA, Identity and NAC 2 years ago

Attached is the screen shot.  If I move the WLC-Permit policy towards the top I can log into the...

Mohammad Ali commented on Radio Interface Reset and Shutdown Frequently in Security and Network Management 2 years ago

I have had that happen too with 2600 series AP.  In my case issue was the DHCP was setup on the IOS...

Mohammad Ali commented on How to use Zero-Touch SmartInstall in Getting Started with LANs 2 years ago

Ah gotcha, its an older router 1841 so I grabbed the latest one I found on the site.  I'll try it...

Mohammad Ali commented on How to use Zero-Touch SmartInstall in Getting Started with LANs 2 years ago

You mean instead of using a router as a Director use a switch or a newer router?

Mohammad Ali commented on How to use Zero-Touch SmartInstall in Getting Started with LANs 2 years ago

Actually sorry I just had it in there as a test because for some reason switch seems to be looking...

Bio

User Badges:
  • Badge.
    Silver
    250 points or more

Mohammad Ali's Stats

Points417
Discussion started 142
Answers marked as Correct 45
Endorsed 0
Content Rated 239