The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
On my Cisco 2960CG running 15.2(2)E10 when I run command show ip igmp snooping detail, among other things I see that IGMPv3 snooping (minimal) is enabled. Why is this feature called minimal? What is missing from normal v3? Is there any official Cisco...
Hello All,I have a 9500 that does not allow EIGRP. How do I enable it on the 9500 series switch?C9500(config-if)#ip router ?isis IS-IS Routing for IPVersion: Version 17.8.1rThank you for your insight.J
a. I initiate a WebEx call on my phone (through WebEx App). Audio is working fine. I then plug in the USBc cable into my phone, CarPlay comes up on the car display. I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...
After searching through other posts, my config seems OK but still strange behaviourasa 9.20 running on FPWR chasisI cannot get in enabled mode when connecting to ASA via console.It used to work but stopped after I played (disable and restore) with aa...
Hello,I'm reaching out regarding a configuration issue we're experiencing with our 2921 router and the 4 port Gigabit EtherSwitch EHWIC card installed. Despite our efforts, we haven't been able to successfully configure the card to allow connections ...
Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...
Hello,could you tell me if there is any way to access Meraki sandbox? When trying to use Always On lab i am unable to access it, i am hitting MFA requirement: "Enter verification code Please open the authenticator app on your mobile device and enter ...
I have a question that I am not understanding about docker networks, Macvlan and ipvlan. In the first example, I want to show you the macvlan bridge mode network. This works correctly for me, I show you what I have done to make it work correctly. 1. ...
Hello,I need guidance with SPA3102.Line 1 is connected to a SIP trunk and I can make calls (outbound) from the analog telephone (ATA)PSTN Line is also connected to the same SIP trunk, and I need to receive calls (incoming) from the trunk number to th...
We are a healthcare facility. For past several months we have had several complaints from users that calls are often full of static. We are running CUCM 12.5(1)SU8 and the phones are primarily 8811 running current firmware. We have replaced phon...
Hello everyone, Does anyone know the attributes to configure to make the CoA type reauth work on an Aruba 2530 switch (16.11)? I managed to make the CoA Disconnect and port bounce working but I don't have the solution for reauth and I need it for pro...
Hello everyoneI'm writting you because I'm actually having a problem with the prompt using ios_command in Ansible.So, I'm sending a command to copy a file from a FTP server. The prompt will ask to confirm the file name, so I'm sending '\r' as the ans...
We have wireless and wired devices that uses Bonjour (mDNS) service to discover each other. I need to configure both wired and wireless devices in the same VLAN . We have Cisco WLC 5520 and APs that support flexconnect feature. I need to configure AP...
Hola, ayer vacié la papelera de grabaciones para dejar espacio libre, creyendo que estaban correctamente descargadas, y hoy me he dado cuenta que me falta una de ellas. ¿Es posible recuperarla todavía? No sé si Webex las almacena por un tiempo despué...