The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
[FAQs ] How Do I communicate with Delta? (24*7#CustomerSupportAssistan헗 -elta 헔헶헿 line's phone number to call and talk with a live 헿헲헽헿헲혀헲헻혁헮혁헶혃헲 fast is ퟏ-(860) ✈200✈8850 // ퟏ-(860) ✈200✈8850 . Select your connection language upon call and choose th...
Hello All, I have a question, I built the following DHCP pool and ACL on the Cisco core. When the ACL is on the computer doesn't able to get IP address from DHCP but when I turn off the ACL it works perfectly fine. So here is the question when comput...
Hi everyone,1. How can I force dual-5ghz radios on a cluster of 3802I in Mobility Express? I know it is possible to set the XOR radio to be 5GHz for each AP. Is there a more efficient way to set for the entire AP group?2. Is it possible to disable th...
hello We have a old fire power that I have no idea how to upgrade. The actual device is a Cisco Firepower 2130 Threat Defense (77) Version 7.0.4 . Cisco Adaptive Security Appliance Software Version 9.16(3)18. and we have a FMC that is Cisco Firepower...
Hello everyone,We would like to use our “old” C2960X devices, which we have in large numbers, to connect simple devices such as printers or PCs that do not require PoE. The goal is to use SGT for these devices. I have already read that it is not poss...
I have a couple of switches that are trunked via a LAN cable from another switch. I noticed that these switches sometimes have a hard time to SSH into. I get the error: "Connection timed out". After a while and a few tries I can connect just fine. I ...
I just bought a Cisco 730 Headset. I've installed the latest firmware (which took a log time to install comparing to other brands) this are the list of problems that I've noticed so far.Clamping force in the ears is too strong to the point of becomin...
trying to migrate our ISE nodes to 3.2 version in a VM-based infrastructure, I am trying to boot VMs into the ise-3.2.0.542a.SPA.x86_64.iso image as obtained from Cisco's software download center but I keep getting the attached error. It is worth no...
SW2(config)#aaa server radius dynamic-authorSW2(config-locsvr-da-radius)#client 192.168.100.210 server-key Test123SW2(config-locsvr-da-radius)#client 192.168.100.220 server-key Test123Those commands means that we set AAA server (ISE1 and ISE2 in this...
We have recently migrated to Cisco Catalyst 9800 and we having an issue with a captive portal/web authentication. in the old 5508 we point to the same portal with no issues. However, the portal doesn't work on the new WLC. We have a publicly signed c...
Hello,I need to enter in rommon to change the confreg because I cannot use "conf t" in the actual configuration.I tried during booting to press "Break" from Putty terminal but is not able to run into rommon.My intention was to check the following lin...
I'm trying to configure IPv6 access for a BGP session and I want to control this through CoPP, to have more control plane security on my Cisco router with IOS, I did an initial configuration and it continues to accept connections from IPs that I didn...
Join the Webex Developer team on May 15th at 7am PT to learn about the capabilities of the Webex Web Calling SDK designed to enhance your application's direct communication capabilities. Learn how to effortlessly integrate fundamental audio calling c...
We are currently evaluating Webex Contact Center as we consider transitioning away from UCCX. In our existing setup, if there are more than three people waiting in the call queue, an email is automatically sent to the supervisors to alert them. I've ...