Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1930454members
1246457discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

CML2.7 Upgrade Failed in Cockpit

Upgraded to Cisco CML 2.7refplat ISO seems to have disappeared from the C drive.Not seeing a way to download such from the 2.7 download page.Running CML 2 in VMware Workstation 17.5.2Need to add images to CML server.The cml-controller is registered.L...

Cisco Switch with 4G router ISP

Hello all,i have a problem.i have 4G router from ISP and the port is connected to HP switch then one of HP ports connected to my Cisco Switchwhen The power is off then on at 4G router .. the 4G router internet light became red and that's mean there i...

Resolved! FTD Software Upgrade - 7.0.4

Hi all,Looking to upgrade our 2110 FTD from 7.0.4 to 7.0.6.2.Do I need upgrade to 7.0.6 first and then to 7.0.6.2?I noticed the software download for both 7.0.6 and 7.0.6.2 were about the same size.However the FMCv 7.0.6.2 was half the size of 7.0.6.

Resolved! ASA 5516 upgrade to 9,16

Hello ASA Gurus, I have an ASA 5516 running 9.9 and I m planning to upgrade to 9.16 (the latest supported version)This ASA is used as a main VPN concentrator,S2S VPNs are kind of mix, Ikev1 with old encryption ciphers, and others with Ikev2 with stro...

AirSail by • Level 1
  • 575 Views
  • 8 replies
  • 0 Helpful votes

Port security

Dears our CTO wants the whole company mac address to be added in a port security so that nobody outside the company can access our network, is there any alternative solution for adding all the mac addresses manually.

BGP Advertising

Hello,Need some help on the below code. we have 2 bgp path ( primary and backup) and i configure 1 subnet to be routed through main path and the rest 3 subnets through backup.on the backup i have the 3 subnet primary and the first subnet as backup ro...

Norman123 by • Level 1
  • 154 Views
  • 4 replies
  • 0 Helpful votes

How to stop paging of commands output on Cisco iOS devices?

Hello Community,Is there any command to turn-off the paging of the commands output on Cisco iOS and display all output without paging? On Dell Switches, there's a command "terminal length 0", but the same doesn't seem available on Cisco iOS.Router#te...

shown username password wrong

I made a mistake with the command Copy start-up running-configuration instead of copy  running-configuration start-up, which showed me a Duplicate sequence number,after that when I am going to open a second cli then shows the Wrong username and passw...

Resolved! Invalid CLI response when provisioning templates

Hi,   I have an intermittent problem where DNA Center seems to error out when provisioning templates to switches, the log says: Message: Unable to push the invalid CLI to the device 192.0.2.2 using protocol ssh2. Invalid CLI -  'terminal width 0'.  C...

Adding AP Licsense to WLC 5808

Hello everyone,I have Cisco WLC 5508 with 120 Access Points Supported.I know this WLC is End of Life and End of Support.Now I need to add more AP to the WLC, but I need to buy AP Adder License.My question: Is Cisco still provide AP Adder License so I...

maldafee by • Level 1
  • 74 Views
  • 2 replies
  • 0 Helpful votes
Load more