The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
object network obj-10.40.40.1nat (inside,switch) static 172.10.10.5What does the above NAT mean? what is the original source, original destination and the translated source?
I have a couple of Cisco Firepowers that I can access thru SSH or the FDM, but I can't console to them?-Software version: 7.0.5-72-Configured with primary and secondary-Base license-Not using FMCCan someone tell me how to get console access? Thank yo...
I want to know if certain DN's can forwarded with the called number. When Caller A DN (111) Calls User B DN(222) which forwards to User C DN(333) . I want Caller A to see DN(222) on caller ID instead of Call A's DN which is what we see typically (1...
Join ThousandEyes' very own @abfentan as he goes into the new Enterprise Network Assurance Specialist Certification! This webinar will provide a guide to the upcoming Designing and Implementing Enterprise Network Assurance exam (300-445). You can exp...
Get a jump start on one of the hottest technology advancements in networking. Network assurance is a rapidly advanced in-demand job skill, and Cisco is releasing a new exam and training that can put you on the fast track to getting "Network Assurance...
I'm involved in the following setup illustrated below. I am Site 4. I have a SIP trunk via the CUBE to Site 1. Calls route between Site 4 and Site 1 with no problem. Is it possible to use Site 1 CUCM, to route calls from Site 4 to Sites 3 or 2? Is it...
Bonjour voici un réseau que j'ai fais sur Packet Tracer. Le principal objectif est la mise en place des ACL. étenduesVoici les ACL déjà configurées : "enableconfigure terminalaccess-list 100 permit ip host 10.0.0.5 10.0.0.8 0.0.0.7access-list 100 pe...
Hi, We have recently deployed Prime 3.10.2 and added a 9800-L (SW 17.6.4) along with 10 X 9130 APs.. On adding the APs to the site maps within Prime, there is no RF heat maps being emitted from them. Just wondering if any has come across this issue a...
Hello world,I am working on creating a custom report based on the stock reports available for our call center. We would like to total the abandoned call for each day, sorted by the hour of the day. I cannot seem to create a report that only shows th...
Hi thereI am assigned to check the issues with this attached network and have managed to remove some hups and redesign the network to what it is now. there were no vlans and it has been configured. the issue is that the internet speed is extremely sl...
Good afternoon,A new client is splitting off from a parent company this Fall. They current have AP1852E-B-K9 and WLC5200 and they want to migrate to 9800-WL. I will have an instance of the 9800-WL stood up before cutover, but once the WAN is moved fr...
FP has routed sub-interfaces as shown in diagram. HostA is able to ping HostB, and vice-versa. FP Vlan20 responds to ping request from HostA. FP Vlan30 responds to ping request from HostB. All works with the following exception, FP Vlan30 does not re...
General question for the community. I'm looking to use a Catalyst 9200 as my internet access switch. Considering bumping my service from 1Gbps to at least 2Gbps and possibly higher. Can the 9200 switch support higher than Gigabit throughput capaci...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: