Steven Williams

Member Since: Jan 14, 2008

English
Steven Williams commented on Netflow Cisco 4500X in LAN, Switching and Routing 1 week ago

So like back in the day didnt you just need to apply the config to a single interface and it would...

Steven Williams commented on MDS adding fcalias after zoning is configured in Storage Networking 3 weeks ago

I think its because I am configuring the PWWN's and this switch is using the SWWN, switch based...

Steven Williams commented on How to connect 3850 with VLANs to 5506? in LAN, Switching and Routing 3 weeks ago

is the 5506 licensed to do sub interfaces? I know back in the day with 5505's without security plus...

Steven Williams commented on Port-Security and meeting rooms in LAN, Switching and Routing 3 weeks ago

TACACS or Radius will work well. 802.1x using Microsoft NPS or Cisco ISE.

Steven Williams commented on vss switch priority in LAN, Switching and Routing 3 weeks ago

i set switch priority for physical reasons. If my top switch is #1 and the bottom switch is #2 i...

Steven Williams commented on ssh and telnet in LAN, Switching and Routing 3 weeks ago

Firstly - Telnet is bad. Its plain text.  you can only set one password on the vty lines. so if you...

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

I figured it out. The wrong SP ports were connected to the SAN. 3 days of my life gone!

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

Ok still not working. I see this from the show zoneset active vsan 10 zone name...

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

that was it. They dont show in the zoneset list until the zone is reactivated...boo Thanks guys!

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

ummmm i think i see the issue..... zoneset name MID_PROD_DR vsan 10 member...

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

Ya i read that alot, but then why is there smart zoning lol.

Steven Williams commented on Single initiator different zones with different targets in Storage Networking 3 weeks ago

I just cant get the blade HBA able to see both targets with this setup so thats why i thought it...

Steven Williams commented on Does GBIC support ether channel in WAN, Routing and Switching 1 month ago

please show out put of the interfaces, the portchannel, and the show etherchannel summary.

Steven Williams commented on Radius Configuration on main router in Additional Communities 1 month ago

What radius are you using? Its very possible your radius configuration is fine on the router and...

Steven Williams commented on Cisco 2504 WLC in Additional Communities 1 month ago

What port did you define as the mgmt port? You mgmt port should be a different subnet then your...

Steven Williams commented on DMVPN in VPN 1 month ago

I assume that when you see a tunnel interface defining the nhs ip address its a spoke. The hub will...

Steven Williams commented on Copying current phone entry in Unified Communications Applications 1 month ago

Works with Super Copy

Steven Williams commented on Copying current phone entry in Unified Communications Applications 1 month ago

Yes from the publisher and db looks good. Unified CM Database Access Local and publisher...

Steven Williams commented on Copying current phone entry in Unified Communications Applications 1 month ago

I have tried Windows 7 using chrome and IE. I have tried MAC using chrome and Safari.... I am...

Steven Williams commented on Copying current phone entry in Unified Communications Applications 1 month ago

Just copy. I am on a mac using chrome.

Steven Williams commented on 5k upgrade in Server Networking 1 month ago

didnt matter. dual home fex....learned my lesson on that.

Steven Williams commented on 5k upgrade in Server Networking 2 months ago

All at once!

Steven Williams commented on NETFLOW and Layer 2 in LAN, Switching and Routing 2 months ago

2960-01(config-flow-exporter)#source port-channel 20Warning: Cannot use a switchport interface as...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

So in the ASA routing table you will see all routes from every vrf downstream due to the one...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

I was just stating examples. I will draw a diagram. This will help. 

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

Ah ok. So here was my thinking. Ospf 10 area 0 on remote site peers with ospf 100 on 4500. Ospf 200...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

OSPF is only learning default route from the ASA, ASA is set for default originate. Yes the remote...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

I guess this will still be an issue because if I kick up another ospf process in vrf red, and dont...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

The ASA does need to know about the remote location subnets for other traffic that hits the...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

ASA is area 0 to the 4500 and area 1 to an upstream layer to edge ASAs. Neighbor ID Pri State Dead...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

Ya sorry its a bit complex. Its because of PCI compliance. We have a 4500X that runs 9 ospf...

Steven Williams commented on Multiple OSPF Processes per VRF in LAN, Switching and Routing 2 months ago

OSPF process 10 in VRF red has a route map filtering inbound, so any other peering ospf process...

Steven Williams commented on Metro E P2P routing in WAN, Routing and Switching 2 months ago

Well 2960XR's don't support vrfs so there goes that idea. Routed layer 3 interface is the winner....

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Is it normal for the endpoint profile to be unknown?

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Ok good Call!! The client wasnt getting the "INTERNET_ONLY" ACL. It was because the airespace box...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

No change. It looks like tha CoA is the issue. And I guess without that working I wont get any...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

the guest vlan is 142 (10.20.42.0) so wouldnt the last rule accomplish this? also from the client i...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Fixed that, it was because when you create the rule its automatically set to deny, so I always...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Here is the internet only acl

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

the client and ISE are trying to communicate over port 8443? Why is the client trying to reach into...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

6/16/1610:15:51.000 AM Jun 16 10:15:51 10.51.100.42 %ASA-6-106015: Deny TCP (no connection) from...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

No still doesnt work. BUt something did change. After the login is successful by the client it...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

correct and I just fixed that. Also I have two ACLs on the controller now. One for internet only...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

This is what splunk is telling me: Jun 16 08:20:50 10.20.0.60 Jun 16 08:20:50 bnapinfise01...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Ok I think I have an idea of whats going on here. But how to fix it. When i look at the radius logs...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

DNS is working now. There wasnt an entry in DNS for the ISE server. so thats working. THis really...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

The screen on these tabs scroll so difficult to screen shot. But the things that I changed were "...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

Yes there was a firewall and I opened that port and see allows now in splunk.  What specifics are...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

now this. Event 5417 Dynamic Authorization failedFailure Reason 11103 RADIUS-Client encountered...

Steven Williams commented on Sponsor Approved Guest Access in AAA, Identity and NAC 3 months ago

It was a deny from my ISE server to the WLC for port 1700. Not sure what thats for. No I am having...

Bio










  • 30 Visits





  • 1000 Added









Steven Williams's Stats

Points37
Discussion started 163
Answers marked as Correct 2
Endorsed 0
Content Rated 26