Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
we've recently bouth 2-3 cheaper Cisco SMB Switch and are now having problems running our Alcatel-Lucent IP Phones on those switches. Due to the Manual IP Phones should be supported but we can't make them running. IP Phones are not able to connect to...
Hello,Our company is looking to set up Cisco Telepresence between 3 locations connected with VPN (and also maybe enabled external calls).We already have a VoIP system in place, with Cisco Routers (2811 and 2901) serving as h323 gateways. My question...
Hello, Jabber for Everyone is no longer needed at CUCM and IM&P 11.X? Regards Leonardo Santana
Hi all, a customer of mine is looking to replace a load of DECT devices and doesnt want the expense of Cisco 792x phones so has sourced a SIP-WiFi by a company called Incom, an ICW-1000G. I have the device on the WiFi and can ping the CUCM servers bu...
Hello everybody, Hope you're doing alright. I was wondering if you could shed some light on this issue since I've doublechecked my config and found nothing unusual so far. My scenario contains a callmanager express and cisco phones (3905 and 7841...
All, CUCM 8.6. 2 phones with 4 extensions each. Is there a way to configure a hunt group or groups so that the first 4 calls ring in on the first 4 lines on Phone 1 and then the next 4 ring in on Phone 2 then back and forth like that all day. If ...
Hello everyone, running CM 8.6(2) and with Attendant Console 8.6(2). This version of AC is only supported on Server 2003 and Server 2008 R1. There is a need to upgrade but I am having trouble determining if we can run a version of AC on Server 20...
Hello, I need to customize the Wallpaper of 8941, but the option of Wallpaper on the IP Phone do not show to the user. I know that on CUCM i need to check this option: "Attention: All file names are case sensitive. If you use list.xml for the file na...
Hello,There is an integrations between Cisco(Cisco Unified CM Administration System version: 9.1.2.10000-28) and Alcatel PBX, the communication is right from both sides, but when there is a call from IP phone from Alcatel to the IP phone from Cisco, ...
HI Team, We have recently purchased Cisco IP Phone 7945G & installed at one of our site. Now We need to procure the Headset for this 7945G IP phone Model. Can you please share the Compatible Headset Model ( Both Wired & wireless ) for this 7945G IP p...
On a VG202 Gateway, can I use the 2nd FAst Ethernet port to connect a PC ? I would like to connect the VG202to a LAN switch, and have a PC behind it on the second Fast Ethernet port. On an analog port, I will connect an analog Fax.In fact, the VG202 ...
Hello! DTMF ISSUE - Service provider supports only in-band dtmf in voice channel, so i need to transcode it to rfc2833 on CUBE SP - g711alaw SIP in-band dtmf - CUBE - g711alaw SIP rfc2833 dtmf - INTERNAL NETWORK Config of CUBE: voice-card 0 ...
Hello, How do I forward incoming calls from ISDN to VoIP? We have a few numbers which are terminated on our ISDN 2 and 30 trunks and I'd like to forward them to a VoIP server. We're running Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Ve...
Hi All, I have configured h323 gateway from hq to pstn . when I try to call the following numbers from hq IP phone to Pstn phone am getting reorder tone . 912012517295 , 914087071222 . The output trace as follows Bearer Capability i = 0x8090A2 ...
Hello. We have CUCM v9.1.2 and phones 9951, 9971. When we tried to organize conference on 9971 (this phone with CKEM module), conference softkey not appeared. Algoritm of our actions: 1. We call from 9971 to second phone 2. Than push to conference bu...
