Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have a new Call Manager 10.5.2.11900-3, online for only 2 months. The Call Manager is a single server virtual machine running on BE6000. At the same time we configured a new Cisco 2921 CUBE to forward all incoming calls to a live receptionist (ext...
We are a small (<100 person) company running CUCME 8.6. Is there a simple way to enable call logging history without having to collect the logs off-box? I am looking for a way to simply keep a log of the past 200-300 calls (we don't do that much ...
Following Dolby's instructions, the phone registers with CUCM and can receive external calls. The problem is it can't make calls...internal or external. When trying to make an external call, I get a busy signal. Calling an internal extension will r...
Hello peopleRecently we updated firmware for phones 78xx (7821 , 7841 , 7861) in CUCM (System version: 8.5.1.10000-26) from firmware version "sip78xx.10-1-1-9" to "sip78xx.10-3-1-12" this as a workaround of problem phones won´t register in CUCM.Now s...
HI AllWe have been facing an issue in our cluster where UCCX cluster has failed over from uccx-1 to uccx-2 as the master . and after some troubleshooting we found that Cisco Bug: CSCul18667 is causing the issue.Now, Cisco Bug: CSCul18667 - CUIC doesn...
Hi All,Could we register a 3905 as a 3rd party SIP phone on a UC540?Thanks in advance,Nick
There are two BE7000M servers, install CUCM11.x, how do I configure both hardware and support 7500 users, the Redundancy model that you choose, in addition to this problem, I still have doubts, the document describes BE7000M supports up to 5000 users...
I have a 10.5 CUCM cluster . I see that some of completed calls from Mobile phones to internal numbers do not seem to appear in the CDR records at all. But on the other hand I made similar calls to other internal extensions which seemed to be seen i...
Dears, I have 7911 ip phone which are not registering to CUCM once I connected it to SG300 switch when I connect the phone to 2960 switch the phone register normally and works fine. I already tested another phones like 7975 and 7841 with SG300 sw...
Dear All, I have 2 questions. 1) Customer has cluster over wan setup and many branches are connected by WAN router and Voice Gateways. When dial from any IP Phone like 79XX series call goes fine without delay. But when dial from DX650 there is delay...
I have 1 UWL license for 2 devices; 1 IP phone and 1 analog (ATA190) same phone number on each phone. I would like to have call waiting set up on both phones so if a second call comes in I can answer it on either phone. Is this possible? If call 1...
Hi We are doing SIP trunk integration between Cisco call manager and NEC SV 8500. From NEC we are able to call Cisco user but one way speech ( Cisco user can hear NEC voice) but from Cisco we are not able to call NEC. Can anyone help me on this ...
Hi, We are running CUCM 8.6 with Single line ( VOIP & PSTN) with Geo location & LRG in place. Also we have UNx 10.5. Current Requirement is 100 users are moving to different location in same cluster. From Location A to Location B. Requirement: Us...
dear sir, am not getting ringback tone on fxo and fxs ports why?
Cisco DX650 trying to dial SIP URI instead of extension for intercluser user. DX650 registered to CUCM 9.1.2 in sydney cluster with all users (US + Sydney). Call a US user from directory, tries to call as first.last@<IP of Sydney Sub> instead of ex...
