Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
How do I assign a role to a user. I`ve given them the admin role as an example but can not log in . What is the GUI log on details I should use Alisa, Extension etc but no luck. The password I`m also using is the VM PIN I use to listen thanks
I have a group of 6 phones that have 6 shared lines. We'll call them phones A-F and extensions 1001-1006. All 6 phones have all 6 shared lines on them. All phones are 9971s with BiB enabled. This group's calls are constantly recorded. The record...
Hi, guys,I tried to configure a device profile for 9971 with two DN lines, and I assigned it to an end userwhich I logged in with into a Cisco IP phone 9971, the problem is that once I logged in, I'm finding onlythe first DN line, the second is miss...
Hello, Is there any chance or a way to know to configure and E1 to have Internet or WAN Access? Thanks
Hello Cisco world I am working on a CUCM expansion and upgrade for a customer.CUCM currently runs on v8.6 with 4 nodes plus licences and we intend to add 2 additional subscribers and update entire cluster to v10.x.My question is, in v8.6, if I add su...
We are using Cisco CM System version: 8.6.2.20000-2..is it possible to find the report of how many & whcih extn belongs to particular CSS
Hi everybody!There ia a problem with paging. We have Cisco CCME ver 9.1, CISCO2921, IOS c2900-universalk9-mz.SPA.152-4.M4.binin the office.I installed paging on 7962 phones with addon 7915 by SKINNY .Also I added phone Cisco 7962 without addon 791...
Hi all,i don't know if it is so obvious but i really can't find a solution!And i can't find enough discussions so that means that i am completely wrong or nobody has tried it before.I can see that my CUCM 9.1 offers 887VA-V subscription as SCCP gatew...
The upgrade docs say that issuing the command "utils iothrottle disable" can decrease upgrade times. But after the upgrade is complete, you should re-enable I/O throttling. What are the downsides to having I/O Throttling permanently disabled? GTG
yesterday we got the "LowAvailableVirtualMemory" alarm on our CUCM 7.1.3 Publisher( been running about three weeks) as the memory usage went over 70%we reloaded the publisher, and it went down to 35% now 24 hours later it is back up to 55%. The Subsc...
HiI'm quite new to CME. I have issue with one telephone which is connected to call manager router across VPN tunnel. I can't hear anything from that telephone but people from side of this telephone hear me very well. It happen only internally in my c...
I am configuring in Cisco Router 3945 with E1 Qsig to contact a MITEL 3300This is the configuration:isdn switch-type primary-qsigcontroller E1 0/1/1 framing NO-CRC4 clock source internal line-termination 75-ohm pri-group timeslots 1-31 service mgcp d...
Hello all. I am looking at implementing BIB recording to QM 8.5 and have a few questions. I was utilizing remote span recording and all was well with that until a recent upgrade that put an intermediate switch in between my 3750's that does not suppo...
In this document "Components and Cables for Cisco TelePresence Endpoints", it says "automatically included with Top Level PID", does it mean it's not necessery to order a separate CP-PWR-CUBE-5= for DX80 unit?
i have CME run om 3945 router with IOS c3900-universalk9-mz.SPA.152-4.M2.bin and we apply translation rule for the incoming and the outgoing calls through E1 and we configured the translation profile under the dial peers , the issue is every random p...
