Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I can't call the UC from the PSTN,but I can call the UC directly by dialing the hunt polit number I set for the UC. This is the dial-peer I set in gateway,the ip address '142.100.64.13' is my CUCM's address,I changed the ip address to my UC's add...
We just upgraded the firmware in preparation for the 10.5 upgrade except 6941 all other phone models time shows correctly on the phone. Time displayed on 6941 is UTC/GMT time. If we downgrade the firmware back to the old one time shows up correct.CUC...
Hiwhen user tries to login into EM services , they are getting an error as " login unsuccessful (7) unknown error " . they are successfully logged int but every this error is displayed . i have restarted EM services it was working fine for 2 days tod...
Hi Guys,I would like to set up a hunt group. My question is can I use a real extension number assigned to a phone to be a pilot number instead of creating a new pilot number. The requirements are if no one is answering a call to an extension 1000 (e...
Hi all! I would like to try this:1 - Connect an IP phone in a switch (without QoS) and generate a lot of traffic in the trunk to force the voice to interruptions.2 - Connect an IP phone in a switch (with QoS) and with the same traffic verify that ...
I have a deployment of CCME CUE 3.1 and 4.3, and I use the CUE with transfer-mode attended. In this case when the CUE transmitting an incoming call to a destination, the caller can not hear the ring-back tone. Also in transfer-mode phone that receiv...
Hi All,I just finished upgrading cucm 9 to cucm 10.0.1. Upgrade completed successfully, but elm now shows insufficient license message. This is a Vmware installation BTW, I doubt that it matters the CUCM 901 worked fine with its ELM. The ELM is cores...
Hi Experts I have strange issue in CME. I have configured the entry directory under the telephony service but when the users try to get these directory is not shown to them. I shows an old extension and name and even when searching by name it is not ...
Hi All, We have install the email client application on DX650 which requires certificate for the authentication. Require certificate pushed by Apps. we installed the certificate. But when we launch the apps it shows the error message "Certificate is ...
Hi All I would like to know how my css and partitions all hang together on my call manager, is there a easy way of seeing this, like a visual or table view etc ? cheers
Hi,I've configured CME 8.6 and all is working fine I can make outgoing calls and incoming on my ISDN line however, how two small issues that I can’t quite figure out. I'm more than certain that the two issues are down to my dial plan. The first one...
We have a SIP connection between Cisco Call Manager v6 and CME through VPNEverything was working fine until we had to restart our Netgear ProSafe VPN (it has a VPN connection to ASA)Now I get these errors in SIP debug: Jun 11 11:53:09.379: //-1/xxxxx...
Hi, I Need same light about the IP Phone tutorial, i would to change the language but in the menu i can't switch the language. Thank you for your help. Best regardsMajed
I was looking at the configuration for PLAR here:http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/8_0_1/ccmcfg/bccm-801-cm/b03dn.html#wp1338158but it's causing me some problems. Specifically, if the directory number to be rung is in a pa...
I am experiencing a problem with 3rd party sip phones (zoiper soft phone and ascom wifi), whereby the phones hit the required call-reject translation pattern when they dial 1234 and the call is blocked. However, no fast-busy tone is heard. Similarly,...
