Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a gatekeeper configured as: zone prefix test-A 8....... blast gw-priority 6 us-gw1 us-gw2zone prefix test-A 8....... gw-default-priority 0zone prefix GlobalDGK-US 8.......zone prefix GlobalDGK-UK 8.......So which entry does the call (destinate...
Running CUCM 9.1 and documentations says Que status can be monitored via a PLK on select models.How do you set a PLK on a 7911? I have not seemed to find a Softkey that says Que status either.Am I missing something?ThanksKevin
internal extenson is 53XX-55XX and external line is 3670100-3670350,how can I configure translation to make PSTN Directly call internal extensions ?The Router is 2911 and line is E1.thx!
Hi guys,I have CUCM 9.1.2 and a 2901 MGCP gateway with a VWIC3-1MFT-T1E1-E1 card and am trying to integrate this with a Seimens PBX.I have been following this guide to help with the config http://www.cisco.com/en/US/solutions/collateral/ns340/ns414/n...
Dear All,One of my customer purchease cisco 3900 cme they have around 150 user .customer dont want E1/T1 they purchease sip line how i can configure SIP line in cisco cme .insted of configuring E1/T1 i need to configure SIP line Please help me ... i ...
Can anybody provide me the part number for SRSV 9.1 license?From Cisco document:"Connection SRSV is a licensed feature for which you need to install the SRSV specific license on the Enterprise License Manager (ELM) server for the central Connection."...
Hi,i have a "little" problem with the 89xx phone series.After upgrading the phone FW at version 9.3.2 or higher the phone display does not longer show the busy message. Only the busy tone is heard at the handset. I have notice that this problem appea...
HiHow can we change the OS pass for cucm running into vmware?
Dear Support Team,I have to setup an E1 on a router to enable me route voice calls to the PSTN how can i achieve that.a. can i use the normal ethernet RJ45 cable for the E1 connection ?
Good morning,I have a Call manager (Cisco router 3845) with the following characteristics :- Product number : C3845-IPVOICEK9-M- IOS : c3845-ipvoicek9-mz.124-15.T7.bin- 2 Gigabit Ethernet interfaces- 2 Channelized (E1 or T1)/PRI portsSo my questions ...
Using Call Manager 8.6 suddenly problem is reported by receptionist that on her Attendant Console telephone icons not appearing on screen.She is not able to verify the status of extension before transffering the call
Hi allI configured Secure conferences on the GW and CUCM and the dspfarm profile is registered with CUCM.Cluster is secure, when I place calls between 2 phones the lock is shown on the phones display.Also when I place calls between Jabbers, jabbers a...
Hi guysCan somebody help us?We have100x 9951 (sip)400x 69xx (sccp)UCM 9.1.2The 9951 sip are flapping between UCM. We idenfied timeout between phones/ucm.After sniffer the network, we identified big number retransmission of packets (from sip phones) a...
Hello,I try to secure call between two IP-phones CIPC.I plug the 2 ip-phones in a LanSwitch which is plugged in a CME router.Non-secure calls are OK, but when I try to revert the Security Mode into ENCRYPTED (server mode secure), the phones are block...
Hello,Call forwarding worked without problems, we could forward our phones to external numbers and everything was ok, when somebody called to my phone, I could got the call to my cell phone.But now when I forward my phone to external number and try ...
