Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
CUCM 8.8.1Due to sharing a SIP phone number (Avtec Radio console) with Cisco 7942- I need to setup a 'rollover' number so the Avtec can answer a second call (it cannot do so without a second DN).I'll give an example.Primary number: 3115 (calls...
Hi everyone,We are implementing IM and Presence (2 nodes v. 9.1.1.31900-1) and CUCM (2 nodes v. 9.1.2.10000-28) and everything was working great until start testing high availability.Jabber clients are registered on CUCM Sub and when we disconnect th...
Hi,I have a requirement to block specific incoming number and we are running the following versionsCall manager version 8.6.2Protocol on PSTN routers is MGCPCan any one have easy steps to configure this and i am new to voice thingsThanks for your hel...
I need to compile information relating to the number of calls our operator handles in a given day, but am unsure how to do this. We are on CM V8.0.3.20000-2, using Fidelus console for the operator phone. Our old system ran reports that would give us ...
I have an odd issue. When my CCM Group has only my Sub in it, inbound PRI calls through the H323 PRI gateway work fine. If I remove the Sub and only put the Pub in the CCM group and reset everything, all of my phones register to the Pub, etc but in...
Hi everyone,I recently upgraded from 8.5 to CUCM 9.1. I already migrated a Hunt Pilot to Native Call Queueing but I have a question, how can I display a Queues Status on the phone?Attached a picture took from Cisco. Is this a real thing or just was t...
Hi All,Please can someone explain the below concept which is used on a particular route pattern.the calling party transformation settings contain that it should use calling party's external phone number mask which will be used while calling any num...
hello everyone i have a customer want update CUCM from 7.1.5 to 9 and i have update it OK on a VMwarebut now they want use their MCS 7835 to run the CUCM 9.....now can i use USB device to install ? because the CUCM 9 ios is too big then DVD.....
Hello.We are three admins of CUCM 8.5 and we use the same administrator user but with different ip's.My question is:Is there any way to know from what ip a DN was erased?.Thanks in advance.
Hi guys,recently i have configured the dot1x security feature on the cisco c3650x switches with IOS 15.2(1)E. But when I added voice vlan to the port, the ip phone can't register.My switch port configuration as below:interface GigabitEthernet0/47 swi...
DearsWhen i try to access my call manager 8.5 through GUIafter entering the username and passwordon the left corner it gives me "Database communication error "Any IdeaThanks in advnaceRegards
Dear AllKindly help us ., I would like to make the load/stress test with CUCM. What is the solution to apply the test ? Is there any freeware/trial to apply this test ?I found the information about the "Sipp" ., I am not sure it is the good solution...
Hi GuysI Was looking for a good link explaining about that configurationIf you can share something it would be great I found this one .Its apply to the CUPS on premises right?http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/im_presence/i...
How is this done?The documentation says some nonsense to this effect:"Calendar integration can only be enabled on an individual basis, however calendar integration can be disabled for all users by removing the last calendar presence gateway from the ...
Hey,I really have difficult time finding the license part# for BE5000 VoiceMail. My customer wants to buy additional 25-user Voicemail license for BE5000. Anyone can help?Thanks,
