Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,We have been getting the following alert daily,From: [mailto:RTMT_Admin@thedominion.ca]Sent: Tuesday, July 10, 2012 2:04 AMTo: voiperrorSubject: [RTMT-ALERT-StandAloneCluster] CallProcessingNodeCpuPeggingProcessor load over configured thresho...
Hi,Have a strange issue where Call Forward is not workingWe can set the call forward and when ringing the phone, it displays that the call is being forwarded to xxxxxxx but xxxxxx doesn't actually ring. The CSS etc.. are all good the phone in questio...
Hi,I am newbie on IP Telephony, and i have a question about the CUBE functionality...i have read the CUBE datasheets and i really don't understand what is the difference between a normal CME and CUBE licensed CME, for example i have installed a 2921 ...
Hi folks,I'm trying to replace two broken phones on my network with two new one but there is no dialtone on them.My call manager express has IOS 12.4(24)T and I have several 7962 an 7911 already registered and functioning from years.The result of "Sh...
Hello,I have a cme with an fxs card on which a fax was working using stcapp,today i got the following: Port Device Device Call Dev Directory DevIdentifier Name State State Type Number Cntl...
Hello allI have setup two seperate voicemail boxes which are being used for two seperate lines on a 7942 phone. All works fine but I get no MWI on handset for secong line. However, the flashing envelope appears on line disaplay......Not sure if this ...
we are having problems with nat alg. I need to know the h323 version, cisco tac needs to know if its version4 or 5. Please help. show gateway does not work in the router
We have Cisco 6513 Equiped with E1 Module. There is a request to configure T37 On-RAMP for about 10 FAX numbers. Unable to find any document from cisco that can tell me if this hardware is supported.Any Help is appriciated.Rakesh Kashyap
Hi voice team,Is there any way to configure the CUCM 8.6 when a call comes in cisco phone name appears instead of the number?Is there somewhere in CUCM that I can register my contacts, so some of them call my extension name appears rather than the nu...
i have tried configuring lpcor for enabling authcode for the making calls for longer distance.Can please some help in configuring the lpcor for cme
Hi Guys, I have the following doubts: In CUCM we have two partitions (Active and Inactive), wright? When I need put another patch, what file will subscribe? the first file or the most recent file? Is it possible remove the previous file?Thanks,Wilson...
Hi there, a quick question: from the following screenshot based on cucm unified CM DB Status, can any one confirm to me that there is database replication issue here. Screenshot A indectate that both database are 2 which is good. but screenshot B s...
Hi，EveryoneI am facing some issues with the backlight dislpay in cisco 7970G and 7965G phone. My Router is 2811 ,CME is 7.1 version. I want all the phones to turn off the backlight dislpay after 1 minute. I have did some mentioned under and there i...
Hi, Facing a critical issue with Cisco Unity Connection. ======================================Problem Description :: Getting alerts for : Connection Database Proxy -- after checking -- the service was activated -- but stopped -- restarted the servic...
I see on several sites a simple digit translation command and they say it works but when I enter it into my 2610XM (CME 4.0.1.0) amd my 2851 (CME 8.6), they both get me the error below.Command: LAB_2610XM(cfg-translation-rule)#rule 1 /2535551......
