Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I have 2 E1 outputs from my Alcatel 4400 PBX. One goes to a 2600 and the other goes to a 2901. They then get fed down separate fibres to our data centre where they enter another 2901 and 2600, exit on E1 to a VoIP server (2901 primary, 2600 s...
Hello. Currently receiving RTMT Alerts, Low Available Virtual Memory below 30%, with tomcat useing most of the memory. I have restarted the tomcat servvice, no help. Similar posts have suggested restarting the RisDC service. Is this the next step...
Hi EveryoneI have a small problem with getting some siemens 40G voip phones to work when connected to cisco 3750's. Basically when I connect the phone will pick up an ip address in the data vlan range and not one in the voice vlan address range. I be...
We are doing a very slow migration from a Rolm 9751 to a CISCO CUCM (7.1.5). We also have Unity 7.1.5 and even UCCX. The migration is done as budget allows, therefore we're trying to keep costs as reasonable as possible. Many departments have old ...
Hi voice team, i configured the extension mobility and works fine, but the customer wants to change the language on ip phone 79XX (login page), how to change the language?Thanks.Thiago Gandara
I have a cisco 2911 with sre/ism for Unity express Is the correct code not ISM-SPA-sme.8.6.1?Please tell me if I am wrong
Hi to all.We have problem with occasional missing RTP stream from phone to recorder. This happens only when recording phone is not in same CUCM Group with remote phone (that is not recorded), eg. not registered on same subscriber. Our setup is as fol...
Hi.Can anyone tell which is the best method to integrate Noortel CS 1000 r 5.5 with CUCM? As we have 9 companies with a fiber cable all companies have all thier own firewall. we are having Nortel PABX and we need integrate with CUCM which is the bes...
Is it possible to get Super G3 or Super G4 faxing to work over CUCM/VoIP ?GTG
Hi,i have one question regarding SRST interoperability with other vendors equipment. In our network, cisco 881 SRST routers are used to connect small branch offices to central site. However, whole network uses Astra platform for VoIP. My question is ...
I am running CME with 7962 phones. When users try to create a conference call they get "unable to connect", this happens the first time the conf button is pressed. Any ideas?
By setting up sip, it seems that it lets anything that connects to it (registered or not, validuser or not) make calls to any dial-peer. How do I go about making it so the sip endpointcan only make a call is if it that sip endpoint registered with cu...
At the moment we use CUCM7 and UCNX8 (only for voicemail)and CUWL pro lic's for all users.I have the task to migrate 500 users to the CUCM, with Extention Mobility.My huge problem is that at the moment all users are member of their departments HuntPi...
Hi eveyone,i have configured CUCM 8.5 and 50 CIPC, almost all of them works well but 5 softphones have the problem below: Invalid SCCP message! : Invalid length = 335544320 - close connection and alarm in futureall CIPC are configured in the same lo...
We have our PRI's coming to our 2950 some of the DID's that are attached to the PRI's are for our GFI Faxmaker server. This server uses a Brooketrout TR114+P4C card 2 ports loop-start ports 0-1 and 2 ports DID ports 2-3. On the 2950 router I have a...
