Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All,I have a problem that I don't know how to attack. We have a call manager at our HQ and a number of MGCP gateways around the country. Most are 2821 ISRs and they all have between 2 and 5 pots lines connected to the pstn. Here's the problem. ...
Dear NetPro gurus,Has anyone see this before??16:16:36 2 CNetAdapterUtil::StartIpPhoneSearch: This PC has 2 network cards...16:16:36 1 CNetAdapterUtil::StartIpPhoneSearch: ignore VPN or Virtual adapter with index 0!And because of these errors, i can'...
What is the best way to troubleshoot infrequent but consistent occurences of this event in RTMT? I know that this event can trigger if keepalives are lost in excess of 2 seconds. Do I have to do a packet capture to determine the root cause? It occurs...
Scenario:PSTN Phone A calls IP Phone B on CUCM cluster via CUBE.PSTN Phone A-------ITSP-----(sip)------------CUBE----------(sip)----------------CUCM--------IP Phone BThis scenario works just fine, Phone A hears ringback always.The problem occurs when...
Hi,I have some problems with setup VLANs in GNS3. The network topology is as on picture: with following details:- router c3700 for CME with VOICE IOS c3725-adventerprisek9-mz.124-15.T7.bin- router c3700 with NM-16ESW module for simulating switch- 2x ...
Hello,Just in case we have one pub and multiple subscribers(2), and i am in the process to add a third subscriber. We have a group of IP Phones that should register as a priority with subscriber#3, while other group should be registered as a priority...
I am standing up call manager 8.6.2 in our lab VM environment for a dry run of the upgrade process. I've been trying to research how to get my data from 7x to 8.x (phones, route patterns, gateways, etc). I know from 4.x to 7.x we had a vendor do th...
We are using a cisco 2911 router as mgcp gateway with one T1 and 4 fxs port. We have an issue of fxs port. Incoming call to the analog phone through fxs port is ok but for outgoing it doesn't work. We set the same CSS as normal ip phone. There is no ...
Guys,I'm really thinking this is a Telco issue but I'd like to get your thoughts on this.On a 3945, I'm receiving a huge amount of RTMT alerts about a PRI going up and down a lot. The Show controller t1 ouutput show a lot of errors:T1 0/0/0 is up. A...
Hi,I have MCS7825-I4 , which in on the compatiblity matrix for the 8.6.1-20000. After upgrading from 8.0 to 8.6.1-20000, none of the services are operational. It just gives the message "This hardware has limited functionality. Backup and Restore is t...
Hi,I am running CCM 8.5.1 and its a 2 node cluster installed in vmware machine.Before changes to hostname, the DB replicate created is 530 and State is 2 for both PUB and SUB.After changes to hostname in SUB, the DB replicate created for SUB is 0 PUB...
I have a user with 7975 set with Jabra wireless GO 6470 , when headset is activein a call, the audio still comes through the handpiece speaker.Can you please let me know is this a bug or there is setting that we can change in phone or CM Thank you
Hello,I am trying to configure a POTS line running to an FXO port on a 2911 router. Currently when i test I get connection (no tones) then the call drops. My path is PSTN --> FXO --> CM (mgcp) -- RightFax. I have a route pattern for the number poi...
Hi , Facing an issue with cisco unity connection problem description : a user has a problem with MWI indicator ( intermittently ) , told that , initially was not able to receive vmail nor was able to get a mwi for that, did a hard reset and all the r...
We have previously blocked the "cfwdall" option throughout the enterprise (callman and CME) but the times have changed and now they want to allow everyone to be able forward their own phones. What is the best way to hand over the administration of t...
