Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I just configured Call Park on my VoIP system and am noticing a very big issue, I have to add each individual user into the Call Park Monitoring group in CUCM. My CUCM is synched up with the LDAP server. Is there no way to add the authenticated user ...
I have a provider that negotiates codecs on outgoing calls on a SIP trunk. I would like to send voice calls with a G.729 preference and fax calls with a G.711 preference. I was thinking that if I can match the fax calling number on the incoming dial-...
Hi, We have about 30 Cisco 7912s that we're going through and trying to troubleshoot. When you power them on it just sits with the Globe and Circular Button lit up the two LED lights next to the up and down keys. Nothing displays on the screens, any ...
Greetings,Is it possible to route incoming calls based on the CLID to a specific extension. The reason for this is to route calls from certain states, say AZ 1520...... to the staff that service that region. I have seen a lot of examples how to rej...
Does anyone have something documented as to when a "shared line" will not be "red", yet the line could be inuse?My end users are driving me crazy over no "Red line" indicating the line is inuse. I don't have enough lines on the phones to give out BL...
Hi all,Is there any way to configure software conference bridge in CME rather than hardware, because I do not have enough PVDMs?Regards,
Hi,I've got a 2-node CUCM cluster running 7.1(5) and some 6941 phone with firmware release 9.0.2. The phones should speak Japanese, German and Dutch by choice.I've installed those locale-packages:cm-locale-combined_network-7.1.5.1000-1.cop.sgncm-loca...
We have had some issues with BAT, so I have uninstalled it from the PUB, but when I try to install again from the plugin page or from the exe. file it always errors out with the following message. You cannont install BAT using terminal services. Ins...
My UCM 6.1.4 publisher is sending serverity 1 alerts to Ciscoworks because it thinks we are low on device license units. I guess low is a subjective term, because I don't think it is low. The available DLUs is low on a percentage of the total, but s...
Hey, Will CUCM 8 support: IP phones 7941 and 7911. (current phones)Currently we have CUCM 6 installed in two of our sites, our third site now requires VOIP and we were considering CUCM 8.thanks
Hello,I have several SIP trunks across a few subscribers and when I go to monitor Sip calls active I can see all but 1 of the SIP trunks. If I do a device search for all SIP trunks I can find it. when I try to add the counter instance I can find the ...
MediaResourceListName : NULL_LISTMediaResourceType : 7AppID : Cisco CallManagerClusterID : StandAloneClusterCUCM-BE 8.X What is this? Type 7 is not (as far as i can figure out) a know type?Anybody??Regards Niels
HiI`m sure i`m just missing something here ,but how can i allow my users to create their own personal SD`s from the web gui ? When i go to web gui and login as user i only see the Line Speed dials eg. adding a SD on a line button ,theren is no Person...
If I am attending a call from “x” extension no and at the same time extension no “y” tries to connect to my extension, it gives ringing sound to “y”. This gives a feeling to “y” that either I am not in place or I am not attending the call… i am using...
I have an SPA8000 that I need to get to work with callmanager 7.0. Any ideas on how to configure this...?
