Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I want to configure a 2811 CME router for SIP trunking with 2 providers. (One is local and the other is through the Internet).Do I need do buy a CUBE license on my CME? If yes what will be the benefit?
Hi,I have a customer having voice gateway with 8 FXO for voice calls and users are connected to CUCM server. the VG is also used for SRST.the customer is having two different departments in which he wants to use the first 4 FXO for one department and...
I have recently tried to set up a Polycom KIRK DECT solution with Cisco CME. The Polycom KIRK Wireless Server 600v3 is on the officially supported list from Polycom using the SCCP for older versions of Cisco CME, but not 8 or 8.5 which I tested it wi...
Hi,I'm new to IPT...what are the helpful debug commands for IP Telephony...Thanks.
Hi All,I Have an issue with 6901 phone, Our CUCM is 7.1.5 2000-6. Always get a reorder tone from the phone, not registering to the CUCM. Configuration done manually on CUCM with SCCP.Switch has inline power, since other model ip phons are working wit...
Hi,I have two SPA941 telephones that I have never used. I have no idea how to configure them but all I would like to do is use them for intra-office communication. In other words, I would like to connect them both to the network and just be able to...
Hi,I'm doing ASA phone proxy and using TLS/SRTP but I'm having issue with my phone i.e. experiencin delay, jitter. how do I alleviate it?Thanks...
Disconnect second line when Hold Call hang upHi,all:I have the follow symptom:A call is received and answered in a extension, a new call ingress in the same extension. The new call is answered, and the first call is put in hold.The problem is that th...
Any one have a good hardware solution for faxing over IP. I'm trying to decide between the VG224 and the IAD devices. I've used VG224s in the past and had decent luck but am wondering if the new IAD devices are any better. I would be going from H....
Hi Alli have the following setup:- 2x3900's at two branches (1 for each branch) OBVIOUSLY LOL-CUCM 7.X cluster at the hq-requirement: phones register to cucm and srst fallback incase wan fails.at first i was going for MGCP, but im struggling with my...
Hello there,I have 2901 router with 2fxo ports and 5 cisco ip phones(extensions: 1101 to1105) in my house. I made the configuration required to make all the phones work and each phone can dial other phones extensions successfully (all internally so f...
Hi,I am having issues with FXO not disconnecting immediately after Outside caller hangs the line before internal extension answers (2921 (IOS 15.1(3)T, CME 8.1). Also, when outside caller establishes call the IP phone will not display caller-id (it w...
Guys,I have a challege to use only one DID/dn for receiving fax as well as voice. i was searching for fax2email solutions which actually requires separate DID/dn for fax & voice.I was told by one fax2email software vednor that CUCM has capability to ...
Hi, I facing a problem in Mobile Connect. I am calling Phone A from Phone B. Simulataneously Phone C (Mobile Phone )configured as a remote phone rings. I pick up the Mobile Phone and answer the call. At this point of time i can able to see the Red Le...
Hi, I need help with programming on a CUCM 6.1.2 and I do not know if this is possible. However I have a 2000 int device that I have to configure as follows: must have the ability to make internal and external calls, but the device can be called only...
