Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,We have two voice routers out of which one router is having SRST supported.1. I would like to know if there is any way that we can transfer the SRST license from the existing srst router to the router which does not have SRST2. If it is possible t...
I'm doing some testing on a Cisco 2851 with multiple PVDM2 chips in it. I have dspfarm enabled and have xcode, MTP and conferencing resources configured and registered with CUCM 6. We have a SIP trunk configured that is set to use a media terminati...
Hi all,I have an script for auto attendant that, in bussines hours forward calls to phones and out of bussines hours forward calls to voice mail.Is possible change when calls go to voice mail and when go to phones via ip phones? for example, dialin s...
Hello,I work on CCM v6 and NETWISE PMOP( standard of the society )This application use CTI ports and route points.Since last week we loose some calls (busy tone) and it's ramdom.In the log on NETWISE we can see :TsTapi1 19:00:06.191 L3 CallInfo: Call...
Hi,We are in the middle of a building move and IP schema restructure. In the interim we are also planing on upgrading CM 4.23 to CM 7.x. If we decide to migrate now to CM7 will it be a problem changing the IP addresses of the SUB and PUB later down ...
Hi everybody,I upgraded my ccm (publisher and subscriber) from 4.2 to 6.1 with cisco DMA.after that i send the .lic file generated by cisco DMA ti cisco licensing and they send me the new license.I uploades the licese to my new call manager and aft...
What is the difference w.r.t to Call Preservation for H.323 & MGCP Gateways ? Which Gateway will preserve an on-going call, MGCP or H.3232 if the WAN link fails ?
Hello,We have 2 Cisco Call Manager in our site and place in 2 different locations connecting via a layer 2 network.They form a cluster group and the production one is the publisher and the DR one is the subscriber.In the DR situation, if the laye...
Is there a way in UCM to have the diverted party shown transformed to the external phone mask when calls are diverted back to the PSTN?Scenario: ITSP to CUBE to UCM --- SIP end-to-end. IP phone is forwarded to PSTN number and diversion headers are en...
Just a quick question.We are curious to know the approximate time that it takes to mirror a single drive on a 7835-H2. This would be by removing one drive in the array and putting in a new one.Someone has said 30 minutes, but I felt that was maybe a ...
Hi,I would like to know if i can install CUCM 7.x in sever MCS 7815I2-K9-CC1?Because i saw in matrix compatibility and only that servers are supported:MCS-7815-I2MCS-7815-I2-IPC1MCS-7815-I2-IPCPMCS7815I2-K9-CMA1Why is that? For example MCS7815I2-K9-...
Hi all,I have a consult, It´s supported the model Multisite WAN with Centralized Call Processing used the UCMExpress??? I don´t find the model in the SRND for UCMExpress......What´s the considerations over this model?? In this model the Ip phone re...
We all know the situation... you're about to get ready for a new install, the servers are in your lab, but the DVDs haven't shipped yet. But since you did the last install, you have a bootable DVD from the last version you installed - but you don't w...
Hi,We have a H.323 Router (with MMoH), and everything works fine except the MoH. I have tried a lot of things, however still it seems to not to coperate.When I press the Hold Button I do get this output from the command, please not that there is 0/0 ...
HiI have CUCMBE installed at one of my customers who have deployed 7911 IP Phones to the users. They have however, just purchased a few 7942 phones which I have configured on the system however when they try and look at the corporate directory from t...
