Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
On in-comming Calls it's cutting the 1 letter of the Call Display Ext Dave Smith show as ave Smith, I check the call manager and Router and i am unable to find the issue. did anyone has the same issue? or is their a bug fix for it ?Thank you for yo...
Hello,I trying to translate the 10 digit DNIS that comes in to a 2811 via PRI to a 5 digit DN begining with "2" only during SRST. Here is what I have configured in the router:voice translation-rule 1 rule 1 /^813446/ /2/ rule 2 /^813513/ /2/ voice-t...
Hi all,I have a problem of hunt pilot and line group, hope you can help me.The following are the situation:Cisco UCM version:7.02Hunt pilot number: 1000, it point to only one Hunt List (HL1) then it point to one line group (LG1)the LG1 has 2 DN, 1001...
Hi all, I have a CME 7.0 installed on a 3825 router with an CUE 7.0 NME. My customer had purchased 70 mailbox but the CUE only says that I can only install 17. I read on the installation manual that license are loaded on factory and I did not see any...
I want to integrate XML services uploaded on Tomcat server with CCM6 and subscribe these services to users and phones ……………….. I already attached the service to CCM6 … but I can’t subscribe users or phones to these services ………………Can you tell me how...
I want to configure clocking on a router with this configuration:QUEEN#show inventoryNAME: "2651XM chassis", DESCR: "2651XM chassis"PID: C2651XM-2FE , VID: 2.0, SN: JAE08083B32NAME: "Enhanced High Density Voice Network Module", DESCR: "Enhanced...
Hello,I try to find a solution for put one user in many call pikup like this :group one : user A,B,C and Zgroup two : user D,E,F and Zif i create 3 callpickup :group 1 : user A,B,Cgroup 2 : user D,E,Fgroup 3 : user Zand link group1 with group3 , gro...
Hi, Having a problem applying firmware on a 7906 IP phone its driving me crazy .. The phone has SIP version sip11.8-3-1s and i'm trying to put sccp on the phone using an isolated network without using the CUCMe iv'e defaulted the settings using the...
The CCME router indicates that the 7940 phones are picking an ip address but the network settings on the phones don't indicate the IP. On the other hand, the 7975 phones has been correctly assigned an IP but the phone doesn't get it's assigned extens...
Does anyone know the way to instruct CCME not to update called number on IP phone screen upon reception alerting message from ISDN line of PSTN gateway during outgoing call. The called number is translated (prefixed) by outgoing pots dial-peer so act...
Dear Networkers,I have CCM 6.0.1-3000-7 cluster installed (1 Publisher + 1 Subscriber).All services are up and running. We have 4 x Cisco 7931 IP Phones. 8 different lines are assigned to each Cisco 7931 IP Phone and Extension Mobility is enabled on ...
Hi, All!Now I have the next problem: on my voice gateway AS5350 I have SIP trunk and PRI. This channels point to the same destination .TOutgoing calls camming from CUCM 7.1.I need to make the outgoing call routing based on incoming calling number, fo...
I'm having trouble freeing DSP resources for hardware conference option.The platform is UC520, CME4.2 with 12.4(11)XW7 IOS.It has following built-in interfaces: 4FXO, 4FXS, 1MoHIt also has a PRI wic.I'm using just the 2 FXO channels and 12 chanels on...
Hi AllAny one know how many translation rules we can configure in a voice gateway. I know we can configure 15 subrules under one rule. Please help me to find answer.Thank youSiraj
hiion the cisco ip phone 7965 model i want to modify softkey but not to add default one.For example i want to add "missed calls" button to the fourth button when the phone is on hook.Is it possible ?
