Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, Does anyone have a sample CME config with dialplan from France ?Many Thanks in Advance,Dirk
Hey Guys,I am running into a situation where the BACD drop through looks like a viable solution without making things too complicated. With Callmanager Express 7.0.1 is there a way to have a opt out for voice mail using DropThrough mode? Thanks for...
Hi everyone, Anyone came across a fax tone every 15 secondes on inbound or outbound voice call, a pitch tone (like for FAX waiting to get a farend carrier).With Call Manager 6.1.2.100 H323 gateway to Cisco 2811 voice gateway using BRI ( Microlink ser...
Hello,I have 5 VG-224 installed and 100% populated. They are running the image:vg224-i6s-mz.124-2.T6.binSome ports don't have dial tone, however, users are able to dial a phone number and they can speak without any problems; I mean, everything works ...
Hi,Does anybody know if the SIP CME supports g729 codec in voice register pool?I mean you can put it there but my phones (which are both g729) cannot talk to one another, I hear silence (711 works fine). I tried implementing transcoder and having one...
Hello,I have a problem with the recognition of T.38 faxes; my customer has migrated its telephony provider to T.38 and the fax Onramp does not work.I think there is a problem in the script recognition, the fax detection. Fax detection script is updat...
Recently converted GW from MGCP to H323. Inbound CNAM is no longer displaying. Is there a config option in the dial-peer? Thanks
I have a setup with 2 receptionists where both phones rings at the same time and whoever is free takes the call. I set this up by creating 2 ephone-dn's with the same Reception DID number. And configured the receptionists on one of their buttons wit...
Scenario: Cisco voice Gateway 2800 series running IOS v.12.4(24)T1. One interface connected to PSTN(ISDN) and other to ip network, facing a sip proxy. When a call is placed from pstn to a BRI port, it matches a dial peer which target is the sip prox...
Hello everyone,I had a tech try to flash this phone to SIP 8.11 from SCCP and they must have done something wrong, because the phone goes from configuring VLAN to TFTP error (0A in little letters next to it) and hangs. The tech said they did a restor...
Hi,I need to integrate CUCM 6.0 with Nortel CS1000M for my client. I put an MGCP gateway and configured QSIG trunk beteween CUCM and PBX. The connectivity is like thisCUCM --> MGCP --> QSIG --> PBX Now the calls are working both ways from IP Phones a...
Need to change Subscriber / Call Transfer/ Transfer incoming calls to a phone/ to Yes, ring extension for. Do you know the comparable setting in Unity Bulk Edit ?thanks
Hi,I have CCM cluster 5.1.3 with Cisco IP Phone 7960G, 7961G, 7940G and 7941G. The IP Phone 7960G and 7940G has Firmware 8.0 (7.0). This CCM Cluster has an NTP Server, When the time was changed, Only this one was changed on the cisco phone 7961G and ...
Hi Guys,Is there a way to see " only resolved questions " or "only 5 rated questions" in a particular forum say "Ip Telephony" ?p.s. I am expecting a reply from Rob :)~Neeraj
My organization purchased a Polycom Soundpoint IP 670 SIP phone. I would like to know howto configure this SIP phone on CUCM 7.0 so that I can use it just like any other Cisco IPphone. Any help on this will be greatly appreciated. Thanks.
