Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all, Im on a new install and have found that when I try to send faxes out, it doesnt work correctly. What I have is a 3825 gateway (MGCP) and CUCM 6.1.3. I have an FXS module in the gateway. I will recieve a call just fine to the fax, but when ...
I need to add device packages to CCM6 to support 7916 expansion module.after adding the device packages I did not find the 7916, then i search the forum and I found this topic:http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%...
Hi,I have configured a transcoder and an ios enhanced conference bridge on a branch office 2821 router (two pvdm2-32).These two are well registered to a ccm 6.1.When I try to make a conference everything seems to be OK (conference connected) but nobo...
UCM 7.1(2), CUPC 7.0(2)When using CUPC dialing in softphone mode succeeds, but not when controlling the user's primary phone through CUPC. Dialing from the phone (minus CUPC) works fine. Any ideas?
Is there a way within CallManager 7.0 to block the outgoing caller ID on a particular group of phones while the display information will still get sent on all other phones?
I put a -timeout call dissconnect 60- command on the port that is getting left off hook. It dosen't seem to work though. any ideas?I call after I put the command in and the call still stays up.
Hi,I have a ccm 7 pub and sub which is replicating changes to each other without any problems. However, we I try to create a DHCP server on the Sub I can't register a 7960 phone. The phone show 'defaulting cm to tftp server' followed by 'phone regi...
hi,Am getting request timeout when i hit missed call under directoies tab rather than extension number with date/time....CCM version is 4.1.3PHone model 7960Remaining models like 7940s are working good...Can u help me out here..reagrds
I have a lobby phone that I would like to automatically ring a helpdesk humber when you lift the handset off the phone. How do you do this?
I have an ISDN line with 2 msn numbers.My router is a 1760 with a vic2-2BRI-NT card and cme.The head number is 2391022222 and the msn number are 2391022238 and 2391022248.I need to route all incoming calls from 2391022238 to extension 230 and all inc...
Is there a way to remotely connect to an IP phone and change its speed duplex?The phone is alreayd registered to a CME.
We have unity connections version 7.X which we upgraded from 1.2 over the weekend. I am woundering if we want to turn on LDAP integration on the connections server will it delete the users we already have in the system like call manager will. Also,...
Hi all,I have a few numbers that are part of our Corprate DDI range that are handled exclusivley by our Telco at Carrier level. These numbers divert to an 0800 number and allow numerous Time of Day routing options and messages to be played.I want to...
When placing a call I am getting a second dial tone. It seems that as soon as the route pattern is matched sending it through a 2801 MGCP gateway I get the second dial tone. Call Manager Business EditionSystem version: 6.1.2.1000-13Any ideas?Thanks,R...
Hello everybodyI have a problem with my cube implementarion. I have cube with inside leg with h323 (CCM 4.1) and a outside leg with SIP. The problem: when a I receive a SIP INVITE req to a new call, after sending 180 Ringing to the remote peer, the G...
