Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Is there a way to program a waiting room set that as soon as it is picked up it will dial the receptionist or security. The set will not be able to dial anything else. I don't know the term to use for this type of feature.
How can I slow the DTMF signals coming out of a vic2-2fxo. Call manager 4.1, cisco 2801 router, Just switched from AT&T pots (no centrex, no 9) to Time Warner Digital Cable, and it won't dial out.. incoming is fine. No other changes have been made....
Hi All,I have upgraded the CUCM server from 6.1.1.2000-3 to 6.1.3.1000-16. After finishing the upgrade, I am getting the below message on the main web page of the CUCMCisco Unified CM AdministrationSystem version: 6.1.3.1000-16Licensing Warnings: ...
We have a remote site, fiber-connected with a single 24-port powered switch. I am getting alot of reports of phones spontaeously resetting. When I look at the CCM Syslog, I see the reason code as Keepalive timeouts. However, QoS is configured on t...
ip source-address ip-address [port port] [any-match | strict-match]What exactly any-match or strict-match does?http://www.cisco.com/en/US/docs/ios/12_2t/12_2t13/srst_v202/SRSTbsic.html does not have a detailed explanation. thanks
Hi allIs it possible to built a server with 6.1.2 or 6.1.3 and restore the backup file from 6.1.1 ? Will all the configurations be loaded into the 6.1.2 as it was in 6.1.1 with none of the bugs ?
How I can secure voice VLAN from CUCM?
In a LAN if i have ip phone sets , can they call them without need for Router or call Manager??
Hi, dear gurus!How can i perform a http request in TCL? is it possibble? In my case I cannot use vxml dialog and cisco-data tag, because this request must be performed after ev_disconnect recieved, and no call leg exists to proceed the dialog (leg vx...
We are currently evaluating a Cisco IP Phone, model 7961G-GE. A nice feature of this device is that it lets you run both a PC and the phone through the same ethernet line. However, we are running into issues with the phone not negotiating speeds pr...
Hi guys ,i have to configure ip phones on CCME to forward call to reception by dial one number .... e.g. if internal users have to call reception and reception extension is 000 so instead of dialing 000 they just dial 9 number and call will forward t...
I have 1 each 7960 and 7940 IP phones that I recently purchased from two different sellers on ebay. I purchased 2 ac adapters from a 3rd seller. All were advertised as operational. I'm not naive enough to believe that both phones are not both bad,...
Hi,I have an ATA running H323 and an analogue phone connected to it. This is configured as a VoIP dial peer on a 2800 ISR H323 voice gateway. I'd like the analogue phone to be able to dial any IP phone on my system by using a short code (last 4 digit...
All, CUCM version 7.012811 MGCP gateway version 12.4(24)Tphone 7962 7942 I am having an issue where want to use ilbc on the call leg from the PRI gateway to the ip phone. When we dial ip phone to ip phone the call is set to use ilbc and we can see t...
We are having some issues with conferencing and had a few questions...It is my understanding that CME has a built-in software conferencing capability to conference 3 users without requiring DSP resources. This appears to work fine as long as all cl...
