Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have an AD integration with CUCM 7.0 for our cluster. We would also like to havethe directory of a seperate office which is on a different cluster. Are there any methods available to do this and if so which is best?I was wondering about connecting...
I have a question about tech-prefix in GW as followed,Requirement:1)Local zone GK, domain: cisco.com That's only command in gatekeeper. 2)Tech prefix: 1 for ccm, 852 for CME.I don't known how to defind tech-prefix in VG, i'm not sure whether the belo...
Hi. I've installed a 2801 CCME system for one of my customers.They have a bunch of DDI numbers. That works great, until someone has a missed call from them. The person with the missed call returns the call, and the head office 'main' system number sh...
Hello,I have registered 3rd-party SIP device(X-lite softphone) in CUCM 6.1 environment. I want to use call pickup feature with X-lite. Is this possible? If possible, how do I set up the button?thanks,
I have a 7925G that I am trying to use with CallManager 6.1.2. But the phone gets stuck at the registering stage. Like it keeps looping. I've downloaded the latest device pack and installed it. Any Suggestions?Not sure if this is related but when I s...
Hi,I have a problem where if I reload the Call Manager publisher, this causes all out going calls to fail on the gateways. Incomming calls are fine. I am able to re-arrange the priority of the gateways and the fault shows up the other gateway too. So...
Hi,I have a CM 5.1.3 system, that has pattern 7000 mapped to an H.323 trunk to a Unity Express system (pilot is 7000).All of the following below WORK :-When I dial 7000 from IP phones, I get the Unity Express Pilot -------> (As Expected)When I f...
Hi, allNow I have some troubles in integrating cisco and Avaya devices. we have created the h.323 trunk between cm5.1 and avaya device, and on avaya if I use routing to transfer the call to the CM5.1 through h.323 trunk there is no problem. but becau...
Hello,we are using a UC500 with ISDN BRI Ports on small locations in Germany.In normal scenario a call forwarding to an external number (i.e. Mobile) would be very easy configured. A call coming in will be dialed out using a second line. But this wil...
HelloI hava a problem with pickup. when I pickup call, has a busy. I check service and setup is correct. Then I solve this case by change number of pickup and assign to DN.Please help me to verify. What a happen of this problem.I use callmanager 4.2(...
All, I have a customer that has a UC520. They have a situation where if a call is on hold for 30 seconds, it rings the phone back (not a tone, but a ring). I want to disable this. Anyone know how?
Hello guys I have a question about a voice mail issue. I have deployed voice mail with unity 5.0. We define the pilot number as 4555, now we would like to be able to access the voice mail from the pstn, now we have a did for this purpose.I try to do...
Hello Guys, I have a Cisco Call Manager 6.1 and I would like to know the history of the calls made by the end user by day, hour, extension, etc... is there any way I can do it ??Thanks for your help
Hi, Our system is CUCM5 with Unity5. We use system transfer to numbers that do not exist in Unity. However, when the lines are busy, the system tranfer hangs up the call right away, instead of sending back a busy signal, which is what I expect. When ...
I have H323 GW, CCM , CME and GK in my network.How to do in GK such that block any E163 ID from H323 devices to register to GK??If this can't be reached in GK, what should i do in CCM and CME to meet the requirement?Thanks
