Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I need to import a couple of thousand ERLS into CER 7.0 (large business has ERLS down to the room level).I've been testing the ERL import tool to try to make sure a large import will work, but even with one record, I get the following output:Number o...
Any ideas on intermitten fax problems on a VG224 setup with MGCP? There's only problems when faxing certain numbers. If you dial them with a phone to listen to the exchange you'll get the first beep, but never completes the handshake, it just then ...
Hello,We have a CME environment with two locations. A 2851 router at Location A and a 2811 router at location B. We have configured the 2851 router for Meet Me (MM) conferencing. The 2851 router has more DSPs and we would like it to accomplish pro...
HiI am trying to upgrade the call manager from 4.2.1 to 6.1.2 .. I am using DMA to migrate all the data.. however how can I migrate the data such as speed dial and personal fast dial?Thankskind regardsRachel
I'm trying to understand what the licensed phone numbers actually mean. For example in a 48 user system, do the Teleworker licenses mean you can only connect a total of 4 wireless phones (i.e. 48 + 4)?The documentation seems to imply the 48 must be l...
Hi,I'm trying to demo SNR.I think I've done all the needed config, but selecting into the Device page the Owner User ID, because the field is grey and I can't select any user.When I try to send the call to my Remote Destination device by pressing the...
Hi All, I am using CUCM 7.0. in the IP phone, I only can see limited network configuration setting, for example I can't see DNS setting. how can I see all network setting on the phone? I've already check enable setting on the phone in CUCM. any sugge...
When applying policy-maps to an interface, which direction is generally preferred and why?outbound on the public interfaceinbound on the private interfaceThanks,John
I have an IP Communicator phone on my desktop. You can make on campus, local, long distance and international calls from the IC. When you call into the IPCC Queue, you are trasferred two times and get a fast busy signal. How can we correct this probl...
Hello,I am trying to fax from a VG224 configured as MGCP. I have a 2821 configured as a H323 CUBE. A Verizon SIP trunk is connected to the 2821. So the fax flow is this: VG224-->H323 CUBE-->SIP-->SIP provider. I can't make it work since the fax call ...
Has any one seen an error as above while trying to log into CCM end user page ? "PD error"
I'm setting up some QOS classes to use with LLQ on some router ports. I've used 95k for each g.711 call in the EF priority queue, but I'm unsure how much bandwidth to use for the call control for each call. We're marking call control at CS3, and the...
Once a day after noon we receive the SDL Link OOS. This is a CCM 4.13 SR7 clusterWe are getting the error between the CCM Publisher and a Subscriber that is on the same LAN switch.We have double checked things like duplex settings. We are getting ...
We have an AS5400XM that we are testing for deployment. One of the scenarios we are testing is to use a SIP phone registered to an asterik PBX which then sends/receives calls to/from the outside world through the AS5400. We have had success with dial...
helo,one of my friend have a network at home using ethernet over power line adaptors and Netgear ethernet switches. they are trying to set up two Cisco 7906G IP phones on the network, To date they not been able to get the phones to work. can you ad...
