Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I've had users indicate to me that MOH is not playing when they are during assisted/warm transfers, conference call initiation, etc. All users have dual-line DN'sSo, Basically, whenever you are putting an active call on "hold" (not actually using th...
Hi; I have a problem in integrating unity express (AIM) 2.3.1 installed in 3845 router with 12.4XY1 release, with CCM 5.0(4) server, what is the recommended gateway to be running between the CCM & the router? I tried SIP trunk with no use and H.323 ...
Hi,I have a phone connected to 2-port FXS card on ISR 2821 router.this router is registered to CCM 6.0.I selected SCCP while adding this voice router to the CCM.The problem is there is no dial-tone on the analogue phone connected to fxs port.Hence we...
HiI am having problems with a T1 circuit (ESF, B8ZS and E&M Winkstart) and CallManager 4.2.controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1-24 type e&m-wink-start!This is terminating on a 2621XM with a NM-HDV.I can successfully mak...
I have a group of users who receive multiple hunt group calls from different external numbers. The external numbers are toll-free numbers which ring to local #'s that are DIDs on the PRI going into CUE 4.2. Each toll-free number is for a specific m...
The cluster in question is running CM5.1The normal operation cpu percentage is around 70-80% on the pub and 60-70 on the sub. There are approximately 450 phones registered.Is it normal to see this level of cpu usage?The process that seems to be hog...
Hi,I have CUCM 6.x and a MGCP gateway with SRST and several FXS ports with analog phones hanging off. I want the analog phones always registered to the SRST gateway rather than CUCM because in the event of a problem with CUCM, I do not want to wait ...
HI all,recently i tried to configure an ISDN connection with CallManager and it works fine but i'm stuck in something and thanks for ur previous posts by the wayI have a range of number from my SP like:from 555501 to 555509 and i want that a predefin...
With a T.37 off-ramp Gateway configuration, with a G3 fax at the receiving end; Is it possible to get status delivery notification when the fax has been delivered to the faxmachine? (In the documentation I only read about MDN messages when the receiv...
Has anyone got any recommendations for a USB handset that works (with hook/keyboard functionality) with Communicator?We have finally got our firewall configured for two way comms through VPN and would like to implement a number of users but all USB h...
I have a Unity 4.x server with no unified messaging and no Unity Inbox licenses. Is there a way to grab a voice mail message as a .wav file to save it somewhere when you don't have any of those licenses?
Hi,I'm using a CCM 4.1 and a Cisco 2801 (adv ip services) with PVDM-64 and VWIC-2MFT-E1.When i try to configure pri-group timeslots using the commands : pri-group timeslots 1-31 service mgcp I have the following error message :%Insufficient resources...
We have a UC520 and 12 PSTN lines from our telephone provider.How do I setup our reception phone 7961GE to have more than 2 lines ring at one time? If both lines are busy at reception, the caller gets a busy signal. I would like the 7961GE to have a ...
I'm trying to create an auto-attendant (not from the opening greeting call handler). When the call goes to a CTI port (which then has a forward all to vm) before the opening auto-attendand greeting the system says "sorry". So callers here "sorry" "...
Does CME 4.2 with 7940G IP Phones have any capability to go give a user to listen in on another car?
